Thread Rating:
  • 1 Vote(s) - 1 Average
  • 1
  • 2
  • 3
  • 4
  • 5
5101, no lights after loading hax v39
#1
Hi,

I loaded hax v39 using parallel jtag. No errors but when I reset modem I see no booting lights at all. I have heard that it might be the standby button might be the cause because hax disable standby button. Is there a way to work around this issue?

Thanks.
Reply
#2
(22-08-2014, 11:30 PM)pendrag Wrote: Hi,

I loaded hax v39 using parallel jtag. No errors but when I reset modem I see no booting lights at all. I have heard that it might be the standby button might be the cause because hax disable standby button. Is there a way to work around this issue?

Thanks.

you installed hax over a stock 5101 that was working properly before you installed hax?
Reply
#3
(22-08-2014, 11:34 PM)newname Wrote:
(22-08-2014, 11:30 PM)pendrag Wrote: Hi,

I loaded hax v39 using parallel jtag. No errors but when I reset modem I see no booting lights at all. I have heard that it might be the standby button might be the cause because hax disable standby button. Is there a way to work around this issue?

Thanks.

you installed hax over a stock 5101 that was working properly before you installed hax?
Yes, it was working properly before loading hax. Booting lights were showing just fine. Thx.
Reply
#4
You killed it.
Reply
#5
(22-08-2014, 11:46 PM)sixteen Wrote: You killed it.

Just to learn from my mistake. What must I had done before loading hax on this model? I am assuming there is nothing I can do now, right?
Reply
#6
flash this on it whith verify and skyp error at 67 percent...
is a full flash hax

https://mega.co.nz/#!MZQy3ZrA!y-0EziWk7E...prE_wXxdLg

i was using whit black cats swarzerkaze,and alwais work,the modem will back to life
Reply
#7
(23-08-2014, 01:56 AM)dragonlord7791 Wrote: flash this on it whith verify and skyp error at 67 percent...
is a full flash hax

https://mega.co.nz/#!MZQy3ZrA!y-0EziWk7E...prE_wXxdLg

i was using whit black cats swarzerkaze,and alwais work,the modem will back to life

Gee, thx man, I will try it and let you know how it goes. Regards.
Reply
#8
(23-08-2014, 01:56 AM)dragonlord7791 Wrote: flash this on it whith verify and skyp error at 67 percent...
is a full flash hax

https://mega.co.nz/#!MZQy3ZrA!y-0EziWk7E...prE_wXxdLg

i was using whit black cats swarzerkaze,and alwais work,the modem will back to life

apparently i did the same thing, do you by any chance have a similar file but with rev 39 on it?
Reply
#9
Reflash with this.

THEN reflash hax 39


Revive the cm with the old, whored-out 5101 dump and then when it boots normally flash Hax. Follow the guides for this.


Attached Files
.bin   001ADE90F5A4.SB5101.VIRGIN.2MB.bin (Size: 2 MB / Downloads: 65)
.bin   haxorware11rev39-LITE.bin (Size: 1.13 MB / Downloads: 53)
Reply
#10
Doesnt he have to flash a boot file before he can flash a 2mb dump?
Reply


Forum Jump:


Users browsing this thread: 3 Guest(s)