+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: 5101, no lights after loading hax v39 (/showthread.php?tid=3235)
Pages:
1
2
5101, no lights after loading hax v39 - pendrag - 22-08-2014
Hi,
I loaded hax v39 using parallel jtag. No errors but when I reset modem I see no booting lights at all. I have heard that it might be the standby button might be the cause because hax disable standby button. Is there a way to work around this issue?
Thanks.
RE: 5101, no lights after loading hax v39 - newname - 22-08-2014
(22-08-2014, 11:30 PM)pendrag Wrote: Hi,
I loaded hax v39 using parallel jtag. No errors but when I reset modem I see no booting lights at all. I have heard that it might be the standby button might be the cause because hax disable standby button. Is there a way to work around this issue?
Thanks.
you installed hax over a stock 5101 that was working properly before you installed hax?
RE: 5101, no lights after loading hax v39 - pendrag - 22-08-2014
(22-08-2014, 11:34 PM)newname Wrote:Yes, it was working properly before loading hax. Booting lights were showing just fine. Thx.(22-08-2014, 11:30 PM)pendrag Wrote: Hi,
I loaded hax v39 using parallel jtag. No errors but when I reset modem I see no booting lights at all. I have heard that it might be the standby button might be the cause because hax disable standby button. Is there a way to work around this issue?
Thanks.
you installed hax over a stock 5101 that was working properly before you installed hax?
RE: 5101, no lights after loading hax v39 - sixteen - 22-08-2014
You killed it.
RE: 5101, no lights after loading hax v39 - pendrag - 22-08-2014
(22-08-2014, 11:46 PM)sixteen Wrote: You killed it.
Just to learn from my mistake. What must I had done before loading hax on this model? I am assuming there is nothing I can do now, right?
RE: 5101, no lights after loading hax v39 - dragonlord7791 - 23-08-2014
flash this on it whith verify and skyp error at 67 percent...
is a full flash hax
https://mega.co.nz/#!MZQy3ZrA!y-0EziWk7EG8IfsQQSGi2oDGsRHIWeXC_prE_wXxdLg
i was using whit black cats swarzerkaze,and alwais work,the modem will back to life
RE: 5101, no lights after loading hax v39 - pendrag - 23-08-2014
(23-08-2014, 01:56 AM)dragonlord7791 Wrote: flash this on it whith verify and skyp error at 67 percent...
is a full flash hax
https://mega.co.nz/#!MZQy3ZrA!y-0EziWk7EG8IfsQQSGi2oDGsRHIWeXC_prE_wXxdLg
i was using whit black cats swarzerkaze,and alwais work,the modem will back to life
Gee, thx man, I will try it and let you know how it goes. Regards.
RE: 5101, no lights after loading hax v39 - raven1783 - 29-01-2015
(23-08-2014, 01:56 AM)dragonlord7791 Wrote: flash this on it whith verify and skyp error at 67 percent...
is a full flash hax
https://mega.co.nz/#!MZQy3ZrA!y-0EziWk7EG8IfsQQSGi2oDGsRHIWeXC_prE_wXxdLg
i was using whit black cats swarzerkaze,and alwais work,the modem will back to life
apparently i did the same thing, do you by any chance have a similar file but with rev 39 on it?
RE: 5101, no lights after loading hax v39 - southernyankey1970 - 01-02-2015
Reflash with this.
THEN reflash hax 39
Revive the cm with the old, whored-out 5101 dump and then when it boots normally flash Hax. Follow the guides for this.
RE: 5101, no lights after loading hax v39 - modembricker - 01-02-2015
Doesnt he have to flash a boot file before he can flash a 2mb dump?