Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Modem gets booted
#21
(29-07-2012, 06:43 AM)Tropical Wrote: Calm Down It Was A Joke.

I dont joke to avoid offending anyone. Im here for the technical part of it.
Reply
#22
What are your signal levels like? anything between -10 and -15 can keep the cm from syncing. Different modems operate on their own....i have one or two that refuse to lock on anything less than -10 and some that will run on -17.

A signal like this is about as pretty as it gets. I bypass the rest of the house with a run of quality RG6 from the tap to my Cm.

Frequency 555000000 Hz
Signal To Noise Ratio 40.0 dB
Power Level 0.6 dBmV
The Downstream Power Level reading is a snapshot taken at the time this page was requested. Please Reload/Refresh this Page for a new reading

Upstream Value
Channel ID 2
Frequency 29600000 Hz
Power 43.4 dBm
Reply
#23
(29-07-2012, 03:43 PM)southernyankey1970 Wrote: What are your signal levels like? anything between -10 and -15 can keep the cm from syncing. Different modems operate on their own....i have one or two that refuse to lock on anything less than -10 and some that will run on -17.

A signal like this is about as pretty as it gets. I bypass the rest of the house with a run of quality RG6 from the tap to my Cm.

Frequency 555000000 Hz
Signal To Noise Ratio 40.0 dB
Power Level 0.6 dBmV
The Downstream Power Level reading is a snapshot taken at the time this page was requested. Please Reload/Refresh this Page for a new reading

Upstream Value
Channel ID 2
Frequency 29600000 Hz
Power 43.4 dBm

This is what I have:

Frequency 681 MHz
Status Locked
Annex DOCSIS

Modulation QAM256

Symbol Rate 5360537 sym/sec
Receive Power -19.2 dBmV
Signal to Noise ratio 31.8 dB


Upstream

Frequency 36 MHz
Channel ID 2



Status Ready

Mode ATDMA
Symbol Rate 5120000 sym/sec
Transmit Power 54.0 dBmV

What you think of it?
    This is what I get. I don't know if this is close to the real speed of the cfg file as far as speedtest goes when doing a test.

Reply
#24
Receive Power -19.2 dBmV
Signal to Noise ratio 31.8 dB

just what I thought...

your modem is deaf. Fix your signal. Do what i did if you can. Too many splitters between you and the tap.
Reply
#25
(29-07-2012, 05:05 PM)southernyankey1970 Wrote: Receive Power -19.2 dBmV
Signal to Noise ratio 31.8 dB

just what I thought...

your modem is deaf. Fix your signal. Do what i did if you can. Too many splitters between you and the tap.

I'll do that sometime this week. Thank you Southernyankey1970.
Reply
#26
(29-07-2012, 05:05 PM)southernyankey1970 Wrote: Receive Power -19.2 dBmV
Signal to Noise ratio 31.8 dB

just what I thought...

your modem is deaf. Fix your signal. Do what i did if you can. Too many splitters between you and the tap.

Well Southernyankey1970 A+ to you take a look. What you think?

Frequency 681 MHz
Status Locked
Annex DOCSIS
Modulation QAM256
Symbol Rate 5360537 sym/sec
Receive Power -14.5 dBmV
Signal to Noise ratio 34.8 dB Upstream




Frequency 36 MHz
Channel ID 2

Status Ready
Mode ATDMA
Symbol Rate 5120000 sym/sec
Transmit Power 53.2 dBmV
Reply
#27
Receive Power -14.5 dBmV Marginal but doable. Config file has nothing to do with the signal quality.

good job. the closer to 0 db the better.
Reply
#28
(30-07-2012, 02:33 AM)southernyankey1970 Wrote: Receive Power -14.5 dBmV Marginal but doable. Config file has nothing to do with the signal quality.

good job. the closer to 0 db the better.

I was mentioning the config file regarding speed testing on Speedtest.net. By the way, is a speedtier cfg suppose to be fast or "special". Or is reserve for higher monthly subscription?
Never mind the question, I found the answer on Cable Inside Scoop.
Reply
#29
should be 22/4
Reply
#30
(30-07-2012, 04:14 AM)southernyankey1970 Wrote: should be 22/4

Yeah, that's about right.
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)