speed crash after ISP update

[newprogram]

stop forcing your modded config and take the one served by the tftp and see what your speed is
as in both the above logs your using/forcing the same config

I delete haxorware config file and custom file from file manager,"Disable Firmware Upgrades" and "Force Network Access" is turn on,but
the speed still save 512KB and 2.7MB,below is telnet log,

Code:

Haxorware integrated telnet daemon

Username: root
Password: **********
Welcome.
CM>
CM> run_app


Running the system...

BcmCmDocsisStatusEventCodes::kCmIsNotOperational
CamDeleteAddress: Deleted address from cam segment 0

CM> Non-Vol Settings successfully written to the device.

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17

mot_scanList: Setting override freq @ 7000000
Scanning DS Channel at 7000000 Hz... (Initial target freq)

mot_scanList: Setting override freq @ 0
Favorite[1].freq = 603000000
Attempting Downstream FEC lock @ freq= 603000000 Hz, QAM64/256

******************************************
            DOWNSTREAM STATUS
******************************************
  Tuner Frequency = 603000000 Hz
   Carrier Offset = -2 Hz
      Symbol rate = 5360537 sym/sec
              SNR = 35 dB
         QAM Mode = QAM256
        Tuner AGC = 0xfff00000
           IF AGC = 0x16267eb8
      Power Level = 0 dB
              QAM = LOCKED
              FEC = LOCKED
******************************************

CM> Selecting UCD for Us Channel 1

RNG-RSP  Adj: tim=2707 power=74 freq=0  Stat=Continue
Non-Vol Settings successfully written to the device.

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
Selecting UCD for Us Channel 3

RNG-RSP  Adj: tim=2707 power=24 freq=0  Stat=Continue
RNG-RSP  Adj: tim=0 power=0 freq=0  Stat=Success

******************************************
            UPSTREAM STATUS
******************************************
       Upstream Status = UP
      Upstream Channel = 3
    Upstream Frequency = 33000000 Hz
        Upstream Power = 39 dBmV
           Ranging SID = 0x2fb
  Upstream Symbol Rate = 2560000 sym/sec
******************************************

Starting IP Initialization with DHCP...
CM> ARPing for default GW IP = 192.168.176.1
MAC = 64:00:f1:3f:4d:d9
DHCP completed successfully!
DHCP: IP address = 192.168.176.23

Starting Time Of Day...
Current system time -> Wed Apr 15 17:30:40 2015

System start time -> Wed Apr 15 17:26:16 2015

Starting Tftp of configuration file...
Resuming SNMP Thread
tftp-enforce bypass is DISABLED
Storing received cfg of size 148 to memory
Time Of Day completed...
BPI initialization completed.  Calling ConfigOperational().
Enabling network access for all CPE ports.

mot_scanList: Writing to Flash!
BcmCmDocsisStatusEventCodes::kCmIsOperational
Suspending SNMP Thread

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
Scanning DS Channel at 621000000 Hz...
Found carrier at 621000000 Hz!
Signal quality = 34.8 dB SNR
Selecting UCD for Us Channel 3

RNG-RSP  Adj: tim=0 power=0 freq=0  Stat=Success
Enabling network access for all CPE ports.

mot_scanList: Writing to Flash!

Is this problem from BPI?[/code]I do not have cert file
when i turn on Tftp Enforce Bypass,BPI initialization completed

Code:

BPI initialization completed.  Calling ConfigOperational().
Enabling network access for all CPE ports.

when i turn off Tftp Enforce Bypass,log show:

Code:

Non-Vol Settings successfully written to the device.

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17