25-02-2012, 08:40 PM
which command? any in particular
------------------------------------------------------------------------------
Command Table: CM DOCSIS Commands (CM)
Description:
CM DOCSIS Commands
Available Commands:
con_high mbufShow memShow mutex_debug ping
read_memory reset routeShow run_app shell
stackShow taskDelete taskInfo taskPrioritySet taskResume
taskShow taskSuspend taskTrace usfsShow version
write_memory zone
----
Available sub-command tables:
[HeapManager] [cm_hal] [docsis_ctl] [embedded_target] [enet_hal] [event_log]
[flash] [forwarder] [ip_hal] [msgLog] [non-vol] [pingHelper] [snmp] [snoop]
[usb_hal]
------------------------------------------------------------------------------
Command Table: HeapManager Commands (HeapManager)
Description:
Broadcom Heap Manager (malloc/free) settings and commands.
Available Commands:
bcheck bcheck_crash bcheck_enable last_error maxAlloc
memShow stats threadUsage trace walk
walk_alloc
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS HAL Commands (cm_hal)
Description:
Commands to show/change the CM DOCSIS HAL state.
Available Commands:
ackcel_show bcmalloc_show bist_test change counters
cpe_add cpe_del cpe_max cpe_print ds_state
hal_show l2vpn_mask ldaix_read lock_ds log
mac_diag map_lead_time_show packets_queued qam_lock
qosParms read_mbr read_posted scan_ds scan_stop
set_mode show show_halif transmit tune
tune_band tuner_read tuner_write us_burst us_cw_transmit
us_debug us_reset us_sweep us_transmit write_mbr
write_posted
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS Control Thread Commands (docsis_ctl)
Description:
Commands to change the state of the DOCSIS Control thread.
Available Commands:
ClearCmCert binarySfid bpiShow cfg_hex_show cfg_tlv_show
clear_image comp_mac_to_phy comp_phy_to_mac copy_image dload
dsdiag dsx_show goto_ds goto_us igmpShow
ip_initialize ip_show l2vpn_show log_messages map_debug
modem_caps rate_shaping_enable rng_rsp scan_stop
showFlows state stop_download ucdShow ucddiag
up_dis us_phy_oh_show usdiag
----
Available sub-command tables:
[dsxTest] [propane_ctl]
------------------------------------------------------------------------------
Command Table: Dynamic Service Test Command Table (dsxTest)
Description:
Commands to test dynamic service.
Available Commands:
addConfigFile autoDsxTest changeConfigFile delRef
delSfids dropDsxMsg dscLocal dsdLocal show
----
------------------------------------------------------------------------------
Command Table: CM Propane Control Thread Commands (propane_ctl)
Description:
Commands to change the state of the Propane Control thread.
Available Commands:
debug discovery dsx_complete oper_caps port_number
psi_grant release_psis request_psis show simulate
----
------------------------------------------------------------------------------
Command Table: Embedded Target Commands (embedded_target)
Description:
Commands to control the embedded target platform.
Available Commands:
bcmalloc_show bcmalloc_walk cache_test cp0_read cp0_write
dcache icache sdram_test start_perf_counters
stop_perf_counters test_bcmalloc
----
------------------------------------------------------------------------------
Command Table: Ethernet HAL Commands (enet_hal)
Description:
Commands to show/change the Ethernet HAL state.
Available Commands:
autoneg force_link full_duplex hal_show read_mii
show speed transmit write_mii
----
------------------------------------------------------------------------------
Command Table: Event Log commands (event_log)
Description:
Commands to manipulate the Event Log
Available Commands:
control flush log_event read show
silent stop_stress stress syslog verbose_show
----
------------------------------------------------------------------------------
Command Table: Flash Driver Commands (flash)
Description:
Commands to control the flash device driver.
Available Commands:
autoTest cfi_show close configRegion deinit
erase init open read readDirect
show write writeArray
----
------------------------------------------------------------------------------
Command Table: Forwarder Commands (forwarder)
Description:
Commands to show/change the Forwarder state.
Available Commands:
filter_logging_enable filter_logging_show halif_show
ip_filter_logging log_packets lt_add lt_clear
lt_delete lt_max_entries lt_show mac_filter_logging
port_filter_logging proto_filter_logging show
----
------------------------------------------------------------------------------
Command Table: IP Stack HAL Commands (ip_hal)
Description:
Commands to manage IP stacks and related tasks.
Available Commands:
bootloader clientif_debug dhcpc_debug dhcpc_show dload
hal_show ip_addr_show ipconfig kill_remote_dhcp_server
lease_show show test
----
------------------------------------------------------------------------------
Command Table: Message Log Settings Commands (msgLog)
Description:
Commands for changing Message Log Settings. These commands allow you enable
and disable display fields and severity levels for individual objects or for
groups of objects.
Available Commands:
fields severities show_settings
----
------------------------------------------------------------------------------
Command Table: Non-Volatile Settings Commands (non-vol)
Description:
Commands to change the non-volatile settings for the application.
Available Commands:
clear_device defaults del_extra_data flush manufactured
read show stats tftp_read tftp_write
write
----
Available sub-command tables:
[Motorola] [bfcApp] [bpi] [docsis] [ds-cal] [event_log] [factory] [halif]
[propane] [snmp_cm] [us-cal] [userif]
------------------------------------------------------------------------------
Command Table: CM Motorola NonVol Commands (Motorola)
Description:
Commands to show/change the CM Vendor (Motorola) NonVol settings.
Available Commands:
clear_device cli_enable cm_amp cm_hwrev cm_tuner
defaults del_extra_data dhcp_enable {flush} html_ro_enable
manufactured read rg_enable show stats
tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: BFC Application Settings Commands (bfcApp)
Description:
Commands to change the non-volatile settings for the BFC Application.
Available Commands:
auto_console clear_device console_stop_prompt defaults
del_extra_data driver_init_prompt {flush} manufactured
read serial_console show stats tftp_read
tftp_write write
----
------------------------------------------------------------------------------
Command Table: CM BPI NonVol Commands (bpi)
Description:
Commands to show/change the CM BPI NonVol settings.
Available Commands:
change_key clear_device code_access cvc_access defaults
del_extra_data {flush} key_location manufactured print
read show stats tftp_read tftp_write
write
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS NonVol Commands (docsis)
Description:
Commands to show/change the CM DOCSIS NonVol settings.
Available Commands:
bpi_version clear_device concat_thresh defaults del_extra_data
dhcp_settings doc10_mcastpromisc ds_frequency enable
fake_reg {flush} ip_stack_number manufactured max_concat
queues rate_shaping_time read rng_class
rng_class_extension show startup_context startup_dsfreq
startup_uschan stats tftp_read tftp_timeout tftp_write
timer_disable ugs_depth ugs_table_entries us_channel
us_power write
----
------------------------------------------------------------------------------
Command Table: DOCSIS CM Downstream Calibration NonVol Commands (ds-cal)
Description:
Commands to show/change the DOCSIS CM Downstream Calibration NonVol settings.
Available Commands:
clear_device clear_tables coef defaults del_extra_data
{flush} frequency ldaix_time manufactured master
num_coef num_freq num_ldaix offset read
show stats tftp_read tftp_write tuner_step
write
----
------------------------------------------------------------------------------
Command Table: DOCSIS EventLog NonVol Commands (event_log)
Description:
Commands to show/change the DOCSIS EventLog NonVol settings.
Available Commands:
clear_device clear_event defaults del_extra_data event
{flush} manufactured read show stats
tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: Factory NonVol Commands (factory)
Description:
Commands to show/change the Factory NonVol settings.
Available Commands:
clear_device defaults del_extra_data {flush} key
manufactured read scratch_pad show sn
stats tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: HalIf NonVol Commands (halif)
Description:
Commands to show/change the HalIf NonVol settings.
Available Commands:
3420_optimized_map DS_AGI DS_AGT STABW1
STABW2 STAGI STAGT STATHR STPGA1
annex_a annex_b bcmalloc bcmalloc_numSizes
board_rev bt_master_enable clear_device cm_1024qam
cm_20_clipping cm_45 cm_45i cm_aboard_v2 cm_aboard_v3
cm_adv_map_runahead cm_amp cm_annex cm_cboard
cm_clc cm_ds_ref_freq cm_iboard_v1a cm_iboard_v1b cm_phy_ref_freq
cm_sboard cm_tuner cm_upstream_priority_queue_support
cm_us_ref_freq cm_us_sample_freq defaults del_extra_data
eth_autoneg eth_duplex_full eth_reject_cam eth_speed {flush}
high_output_pa hpna_message_level interfaces
local_bt_mac_address mac_address manufactured
power_save_enable read remote_bt_mac_address
scdma_code_matrix shack_tries show spreader_scale
stats tftp_read tftp_write usb_device_id usb_mac_address
usb_rndis usb_vendor_id wdog_enable wdog_timeout write
zone
----
------------------------------------------------------------------------------
Command Table: CM Propane NonVol Commands (propane)
Description:
Commands to show/change the CM Propane NonVol settings.
Available Commands:
clear_device defaults del_extra_data enable_propane {flush}
manufactured read show stats tftp_read
tftp_write timer write
----
------------------------------------------------------------------------------
Command Table: CM SNMP NonVol Commands (snmp_cm)
Description:
Commands to show/change the SNMP NonVol settings.
Available Commands:
allow_config clear_device defaults del_extra_data
diag_disable_post_reg dload_tries docsDevSerialNumber
docsDevSwAdminStatus docsDevSwCurrentVers
docsDevSwFilename docsDevSwOperStatus docsDevSwServer
{flush} hide_ipstack_ifentries ip_def_ignore llc_unm_ignore
manufactured max_dload_tries read show single_ip_filt
stats sysContact sysDescr sysLocation sysName
sysORDescr sysORID sysObjectId sysServices tftp_read
tftp_write vendor_name write
----
------------------------------------------------------------------------------
Command Table: DOCSIS CM Upstream Calibration NonVol Commands (us-cal)
Description:
Commands to show/change the DOCSIS CM Upstream Calibration NonVol settings.
Available Commands:
board_rev clear_device clear_table cm_amp config
control def_table defaults del_extra_data {flush}
manufactured offset print read show
stats tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: User Interface NonVol Commands (userif)
Description:
Commands to show/change the Message Log NonVol settings.
Available Commands:
clear_device defaults del_extra_data dhcp_settings fields
{flush} http_acl_host_add http_acl_host_remove
http_acl_hosts_clear http_admin http_adv_ipstacks
http_enable http_ipstacks http_password_idle_timeout
http_password_seed http_socket_show http_user
inactivity_timeout ip_stack_number manufactured password
read severities show ssh_enable ssh_ipstacks
stats telnet_enable telnet_ipstacks tftp_read tftp_write
user_name write
----
------------------------------------------------------------------------------
Command Table: Ping Commands (pingHelper)
Description:
Ping Helper Thread settings and commands. These commands allow you to set the
ping utility up with precise control over packet sizes, timeout values, etc.
Available Commands:
all_sizes end_size hs_nowait hs_wait ip_address
ip_stack ip_sweep number_of_pings ping
restore_defaults show_settings start_size stats
step_amount stop time_between_pings verbosity
verify_enable wait_enable wait_time
----
------------------------------------------------------------------------------
Command Table: SNMP Commands (snmp)
Description:
SNMP commands.
Available Commands:
agent_core_show cm_cfgfile cm_filter_test debug flush
get group_members install_group key_v3 log
n2m notify_setup parent_chain set severities
show test thread_info throttle trap
view_v1v2
----
------------------------------------------------------------------------------
Command Table: Snoop Commands (snoop)
Description:
Commands to show/change the state of Snoop objects.
Available Commands:
debug enable priority show
----
------------------------------------------------------------------------------
Command Table: USB HAL Commands (usb_hal)
Description:
Commands to show/change the USB HAL state.
Available Commands:
hal_show show
----
------------------------------------------------------------------------------
------------------------------------------------------------------------------
Command Table: CM DOCSIS Commands (CM)
Description:
CM DOCSIS Commands
Available Commands:
con_high mbufShow memShow mutex_debug ping
read_memory reset routeShow run_app shell
stackShow taskDelete taskInfo taskPrioritySet taskResume
taskShow taskSuspend taskTrace usfsShow version
write_memory zone
----
Available sub-command tables:
[HeapManager] [cm_hal] [docsis_ctl] [embedded_target] [enet_hal] [event_log]
[flash] [forwarder] [ip_hal] [msgLog] [non-vol] [pingHelper] [snmp] [snoop]
[usb_hal]
------------------------------------------------------------------------------
Command Table: HeapManager Commands (HeapManager)
Description:
Broadcom Heap Manager (malloc/free) settings and commands.
Available Commands:
bcheck bcheck_crash bcheck_enable last_error maxAlloc
memShow stats threadUsage trace walk
walk_alloc
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS HAL Commands (cm_hal)
Description:
Commands to show/change the CM DOCSIS HAL state.
Available Commands:
ackcel_show bcmalloc_show bist_test change counters
cpe_add cpe_del cpe_max cpe_print ds_state
hal_show l2vpn_mask ldaix_read lock_ds log
mac_diag map_lead_time_show packets_queued qam_lock
qosParms read_mbr read_posted scan_ds scan_stop
set_mode show show_halif transmit tune
tune_band tuner_read tuner_write us_burst us_cw_transmit
us_debug us_reset us_sweep us_transmit write_mbr
write_posted
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS Control Thread Commands (docsis_ctl)
Description:
Commands to change the state of the DOCSIS Control thread.
Available Commands:
ClearCmCert binarySfid bpiShow cfg_hex_show cfg_tlv_show
clear_image comp_mac_to_phy comp_phy_to_mac copy_image dload
dsdiag dsx_show goto_ds goto_us igmpShow
ip_initialize ip_show l2vpn_show log_messages map_debug
modem_caps rate_shaping_enable rng_rsp scan_stop
showFlows state stop_download ucdShow ucddiag
up_dis us_phy_oh_show usdiag
----
Available sub-command tables:
[dsxTest] [propane_ctl]
------------------------------------------------------------------------------
Command Table: Dynamic Service Test Command Table (dsxTest)
Description:
Commands to test dynamic service.
Available Commands:
addConfigFile autoDsxTest changeConfigFile delRef
delSfids dropDsxMsg dscLocal dsdLocal show
----
------------------------------------------------------------------------------
Command Table: CM Propane Control Thread Commands (propane_ctl)
Description:
Commands to change the state of the Propane Control thread.
Available Commands:
debug discovery dsx_complete oper_caps port_number
psi_grant release_psis request_psis show simulate
----
------------------------------------------------------------------------------
Command Table: Embedded Target Commands (embedded_target)
Description:
Commands to control the embedded target platform.
Available Commands:
bcmalloc_show bcmalloc_walk cache_test cp0_read cp0_write
dcache icache sdram_test start_perf_counters
stop_perf_counters test_bcmalloc
----
------------------------------------------------------------------------------
Command Table: Ethernet HAL Commands (enet_hal)
Description:
Commands to show/change the Ethernet HAL state.
Available Commands:
autoneg force_link full_duplex hal_show read_mii
show speed transmit write_mii
----
------------------------------------------------------------------------------
Command Table: Event Log commands (event_log)
Description:
Commands to manipulate the Event Log
Available Commands:
control flush log_event read show
silent stop_stress stress syslog verbose_show
----
------------------------------------------------------------------------------
Command Table: Flash Driver Commands (flash)
Description:
Commands to control the flash device driver.
Available Commands:
autoTest cfi_show close configRegion deinit
erase init open read readDirect
show write writeArray
----
------------------------------------------------------------------------------
Command Table: Forwarder Commands (forwarder)
Description:
Commands to show/change the Forwarder state.
Available Commands:
filter_logging_enable filter_logging_show halif_show
ip_filter_logging log_packets lt_add lt_clear
lt_delete lt_max_entries lt_show mac_filter_logging
port_filter_logging proto_filter_logging show
----
------------------------------------------------------------------------------
Command Table: IP Stack HAL Commands (ip_hal)
Description:
Commands to manage IP stacks and related tasks.
Available Commands:
bootloader clientif_debug dhcpc_debug dhcpc_show dload
hal_show ip_addr_show ipconfig kill_remote_dhcp_server
lease_show show test
----
------------------------------------------------------------------------------
Command Table: Message Log Settings Commands (msgLog)
Description:
Commands for changing Message Log Settings. These commands allow you enable
and disable display fields and severity levels for individual objects or for
groups of objects.
Available Commands:
fields severities show_settings
----
------------------------------------------------------------------------------
Command Table: Non-Volatile Settings Commands (non-vol)
Description:
Commands to change the non-volatile settings for the application.
Available Commands:
clear_device defaults del_extra_data flush manufactured
read show stats tftp_read tftp_write
write
----
Available sub-command tables:
[Motorola] [bfcApp] [bpi] [docsis] [ds-cal] [event_log] [factory] [halif]
[propane] [snmp_cm] [us-cal] [userif]
------------------------------------------------------------------------------
Command Table: CM Motorola NonVol Commands (Motorola)
Description:
Commands to show/change the CM Vendor (Motorola) NonVol settings.
Available Commands:
clear_device cli_enable cm_amp cm_hwrev cm_tuner
defaults del_extra_data dhcp_enable {flush} html_ro_enable
manufactured read rg_enable show stats
tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: BFC Application Settings Commands (bfcApp)
Description:
Commands to change the non-volatile settings for the BFC Application.
Available Commands:
auto_console clear_device console_stop_prompt defaults
del_extra_data driver_init_prompt {flush} manufactured
read serial_console show stats tftp_read
tftp_write write
----
------------------------------------------------------------------------------
Command Table: CM BPI NonVol Commands (bpi)
Description:
Commands to show/change the CM BPI NonVol settings.
Available Commands:
change_key clear_device code_access cvc_access defaults
del_extra_data {flush} key_location manufactured print
read show stats tftp_read tftp_write
write
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS NonVol Commands (docsis)
Description:
Commands to show/change the CM DOCSIS NonVol settings.
Available Commands:
bpi_version clear_device concat_thresh defaults del_extra_data
dhcp_settings doc10_mcastpromisc ds_frequency enable
fake_reg {flush} ip_stack_number manufactured max_concat
queues rate_shaping_time read rng_class
rng_class_extension show startup_context startup_dsfreq
startup_uschan stats tftp_read tftp_timeout tftp_write
timer_disable ugs_depth ugs_table_entries us_channel
us_power write
----
------------------------------------------------------------------------------
Command Table: DOCSIS CM Downstream Calibration NonVol Commands (ds-cal)
Description:
Commands to show/change the DOCSIS CM Downstream Calibration NonVol settings.
Available Commands:
clear_device clear_tables coef defaults del_extra_data
{flush} frequency ldaix_time manufactured master
num_coef num_freq num_ldaix offset read
show stats tftp_read tftp_write tuner_step
write
----
------------------------------------------------------------------------------
Command Table: DOCSIS EventLog NonVol Commands (event_log)
Description:
Commands to show/change the DOCSIS EventLog NonVol settings.
Available Commands:
clear_device clear_event defaults del_extra_data event
{flush} manufactured read show stats
tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: Factory NonVol Commands (factory)
Description:
Commands to show/change the Factory NonVol settings.
Available Commands:
clear_device defaults del_extra_data {flush} key
manufactured read scratch_pad show sn
stats tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: HalIf NonVol Commands (halif)
Description:
Commands to show/change the HalIf NonVol settings.
Available Commands:
3420_optimized_map DS_AGI DS_AGT STABW1
STABW2 STAGI STAGT STATHR STPGA1
annex_a annex_b bcmalloc bcmalloc_numSizes
board_rev bt_master_enable clear_device cm_1024qam
cm_20_clipping cm_45 cm_45i cm_aboard_v2 cm_aboard_v3
cm_adv_map_runahead cm_amp cm_annex cm_cboard
cm_clc cm_ds_ref_freq cm_iboard_v1a cm_iboard_v1b cm_phy_ref_freq
cm_sboard cm_tuner cm_upstream_priority_queue_support
cm_us_ref_freq cm_us_sample_freq defaults del_extra_data
eth_autoneg eth_duplex_full eth_reject_cam eth_speed {flush}
high_output_pa hpna_message_level interfaces
local_bt_mac_address mac_address manufactured
power_save_enable read remote_bt_mac_address
scdma_code_matrix shack_tries show spreader_scale
stats tftp_read tftp_write usb_device_id usb_mac_address
usb_rndis usb_vendor_id wdog_enable wdog_timeout write
zone
----
------------------------------------------------------------------------------
Command Table: CM Propane NonVol Commands (propane)
Description:
Commands to show/change the CM Propane NonVol settings.
Available Commands:
clear_device defaults del_extra_data enable_propane {flush}
manufactured read show stats tftp_read
tftp_write timer write
----
------------------------------------------------------------------------------
Command Table: CM SNMP NonVol Commands (snmp_cm)
Description:
Commands to show/change the SNMP NonVol settings.
Available Commands:
allow_config clear_device defaults del_extra_data
diag_disable_post_reg dload_tries docsDevSerialNumber
docsDevSwAdminStatus docsDevSwCurrentVers
docsDevSwFilename docsDevSwOperStatus docsDevSwServer
{flush} hide_ipstack_ifentries ip_def_ignore llc_unm_ignore
manufactured max_dload_tries read show single_ip_filt
stats sysContact sysDescr sysLocation sysName
sysORDescr sysORID sysObjectId sysServices tftp_read
tftp_write vendor_name write
----
------------------------------------------------------------------------------
Command Table: DOCSIS CM Upstream Calibration NonVol Commands (us-cal)
Description:
Commands to show/change the DOCSIS CM Upstream Calibration NonVol settings.
Available Commands:
board_rev clear_device clear_table cm_amp config
control def_table defaults del_extra_data {flush}
manufactured offset print read show
stats tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: User Interface NonVol Commands (userif)
Description:
Commands to show/change the Message Log NonVol settings.
Available Commands:
clear_device defaults del_extra_data dhcp_settings fields
{flush} http_acl_host_add http_acl_host_remove
http_acl_hosts_clear http_admin http_adv_ipstacks
http_enable http_ipstacks http_password_idle_timeout
http_password_seed http_socket_show http_user
inactivity_timeout ip_stack_number manufactured password
read severities show ssh_enable ssh_ipstacks
stats telnet_enable telnet_ipstacks tftp_read tftp_write
user_name write
----
------------------------------------------------------------------------------
Command Table: Ping Commands (pingHelper)
Description:
Ping Helper Thread settings and commands. These commands allow you to set the
ping utility up with precise control over packet sizes, timeout values, etc.
Available Commands:
all_sizes end_size hs_nowait hs_wait ip_address
ip_stack ip_sweep number_of_pings ping
restore_defaults show_settings start_size stats
step_amount stop time_between_pings verbosity
verify_enable wait_enable wait_time
----
------------------------------------------------------------------------------
Command Table: SNMP Commands (snmp)
Description:
SNMP commands.
Available Commands:
agent_core_show cm_cfgfile cm_filter_test debug flush
get group_members install_group key_v3 log
n2m notify_setup parent_chain set severities
show test thread_info throttle trap
view_v1v2
----
------------------------------------------------------------------------------
Command Table: Snoop Commands (snoop)
Description:
Commands to show/change the state of Snoop objects.
Available Commands:
debug enable priority show
----
------------------------------------------------------------------------------
Command Table: USB HAL Commands (usb_hal)
Description:
Commands to show/change the USB HAL state.
Available Commands:
hal_show show
----
------------------------------------------------------------------------------
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
******new discord chat link https://discord.gg/5BQQbsb*******