+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: haxorware webshell command (/showthread.php?tid=1442)
haxorware webshell command - subhani - 25-02-2012
dear sir, please tell me about haxorware webshell command in which command to put in haxorware webshell advance thanks
RE: haxorware webshell command - drewmerc - 25-02-2012
which command? any in particular
------------------------------------------------------------------------------
Command Table: CM DOCSIS Commands (CM)
Description:
CM DOCSIS Commands
Available Commands:
con_high mbufShow memShow mutex_debug ping
read_memory reset routeShow run_app shell
stackShow taskDelete taskInfo taskPrioritySet taskResume
taskShow taskSuspend taskTrace usfsShow version
write_memory zone
----
Available sub-command tables:
[HeapManager] [cm_hal] [docsis_ctl] [embedded_target] [enet_hal] [event_log]
[flash] [forwarder] [ip_hal] [msgLog] [non-vol] [pingHelper] [snmp] [snoop]
[usb_hal]
------------------------------------------------------------------------------
Command Table: HeapManager Commands (HeapManager)
Description:
Broadcom Heap Manager (malloc/free) settings and commands.
Available Commands:
bcheck bcheck_crash bcheck_enable last_error maxAlloc
memShow stats threadUsage trace walk
walk_alloc
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS HAL Commands (cm_hal)
Description:
Commands to show/change the CM DOCSIS HAL state.
Available Commands:
ackcel_show bcmalloc_show bist_test change counters
cpe_add cpe_del cpe_max cpe_print ds_state
hal_show l2vpn_mask ldaix_read lock_ds log
mac_diag map_lead_time_show packets_queued qam_lock
qosParms read_mbr read_posted scan_ds scan_stop
set_mode show show_halif transmit tune
tune_band tuner_read tuner_write us_burst us_cw_transmit
us_debug us_reset us_sweep us_transmit write_mbr
write_posted
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS Control Thread Commands (docsis_ctl)
Description:
Commands to change the state of the DOCSIS Control thread.
Available Commands:
ClearCmCert binarySfid bpiShow cfg_hex_show cfg_tlv_show
clear_image comp_mac_to_phy comp_phy_to_mac copy_image dload
dsdiag dsx_show goto_ds goto_us igmpShow
ip_initialize ip_show l2vpn_show log_messages map_debug
modem_caps rate_shaping_enable rng_rsp scan_stop
showFlows state stop_download ucdShow ucddiag
up_dis us_phy_oh_show usdiag
----
Available sub-command tables:
[dsxTest] [propane_ctl]
------------------------------------------------------------------------------
Command Table: Dynamic Service Test Command Table (dsxTest)
Description:
Commands to test dynamic service.
Available Commands:
addConfigFile autoDsxTest changeConfigFile delRef
delSfids dropDsxMsg dscLocal dsdLocal show
----
------------------------------------------------------------------------------
Command Table: CM Propane Control Thread Commands (propane_ctl)
Description:
Commands to change the state of the Propane Control thread.
Available Commands:
debug discovery dsx_complete oper_caps port_number
psi_grant release_psis request_psis show simulate
----
------------------------------------------------------------------------------
Command Table: Embedded Target Commands (embedded_target)
Description:
Commands to control the embedded target platform.
Available Commands:
bcmalloc_show bcmalloc_walk cache_test cp0_read cp0_write
dcache icache sdram_test start_perf_counters
stop_perf_counters test_bcmalloc
----
------------------------------------------------------------------------------
Command Table: Ethernet HAL Commands (enet_hal)
Description:
Commands to show/change the Ethernet HAL state.
Available Commands:
autoneg force_link full_duplex hal_show read_mii
show speed transmit write_mii
----
------------------------------------------------------------------------------
Command Table: Event Log commands (event_log)
Description:
Commands to manipulate the Event Log
Available Commands:
control flush log_event read show
silent stop_stress stress syslog verbose_show
----
------------------------------------------------------------------------------
Command Table: Flash Driver Commands (flash)
Description:
Commands to control the flash device driver.
Available Commands:
autoTest cfi_show close configRegion deinit
erase init open read readDirect
show write writeArray
----
------------------------------------------------------------------------------
Command Table: Forwarder Commands (forwarder)
Description:
Commands to show/change the Forwarder state.
Available Commands:
filter_logging_enable filter_logging_show halif_show
ip_filter_logging log_packets lt_add lt_clear
lt_delete lt_max_entries lt_show mac_filter_logging
port_filter_logging proto_filter_logging show
----
------------------------------------------------------------------------------
Command Table: IP Stack HAL Commands (ip_hal)
Description:
Commands to manage IP stacks and related tasks.
Available Commands:
bootloader clientif_debug dhcpc_debug dhcpc_show dload
hal_show ip_addr_show ipconfig kill_remote_dhcp_server
lease_show show test
----
------------------------------------------------------------------------------
Command Table: Message Log Settings Commands (msgLog)
Description:
Commands for changing Message Log Settings. These commands allow you enable
and disable display fields and severity levels for individual objects or for
groups of objects.
Available Commands:
fields severities show_settings
----
------------------------------------------------------------------------------
Command Table: Non-Volatile Settings Commands (non-vol)
Description:
Commands to change the non-volatile settings for the application.
Available Commands:
clear_device defaults del_extra_data flush manufactured
read show stats tftp_read tftp_write
write
----
Available sub-command tables:
[Motorola] [bfcApp] [bpi] [docsis] [ds-cal] [event_log] [factory] [halif]
[propane] [snmp_cm] [us-cal] [userif]
------------------------------------------------------------------------------
Command Table: CM Motorola NonVol Commands (Motorola)
Description:
Commands to show/change the CM Vendor (Motorola) NonVol settings.
Available Commands:
clear_device cli_enable cm_amp cm_hwrev cm_tuner
defaults del_extra_data dhcp_enable {flush} html_ro_enable
manufactured read rg_enable show stats
tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: BFC Application Settings Commands (bfcApp)
Description:
Commands to change the non-volatile settings for the BFC Application.
Available Commands:
auto_console clear_device console_stop_prompt defaults
del_extra_data driver_init_prompt {flush} manufactured
read serial_console show stats tftp_read
tftp_write write
----
------------------------------------------------------------------------------
Command Table: CM BPI NonVol Commands (bpi)
Description:
Commands to show/change the CM BPI NonVol settings.
Available Commands:
change_key clear_device code_access cvc_access defaults
del_extra_data {flush} key_location manufactured print
read show stats tftp_read tftp_write
write
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS NonVol Commands (docsis)
Description:
Commands to show/change the CM DOCSIS NonVol settings.
Available Commands:
bpi_version clear_device concat_thresh defaults del_extra_data
dhcp_settings doc10_mcastpromisc ds_frequency enable
fake_reg {flush} ip_stack_number manufactured max_concat
queues rate_shaping_time read rng_class
rng_class_extension show startup_context startup_dsfreq
startup_uschan stats tftp_read tftp_timeout tftp_write
timer_disable ugs_depth ugs_table_entries us_channel
us_power write
----
------------------------------------------------------------------------------
Command Table: DOCSIS CM Downstream Calibration NonVol Commands (ds-cal)
Description:
Commands to show/change the DOCSIS CM Downstream Calibration NonVol settings.
Available Commands:
clear_device clear_tables coef defaults del_extra_data
{flush} frequency ldaix_time manufactured master
num_coef num_freq num_ldaix offset read
show stats tftp_read tftp_write tuner_step
write
----
------------------------------------------------------------------------------
Command Table: DOCSIS EventLog NonVol Commands (event_log)
Description:
Commands to show/change the DOCSIS EventLog NonVol settings.
Available Commands:
clear_device clear_event defaults del_extra_data event
{flush} manufactured read show stats
tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: Factory NonVol Commands (factory)
Description:
Commands to show/change the Factory NonVol settings.
Available Commands:
clear_device defaults del_extra_data {flush} key
manufactured read scratch_pad show sn
stats tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: HalIf NonVol Commands (halif)
Description:
Commands to show/change the HalIf NonVol settings.
Available Commands:
3420_optimized_map DS_AGI DS_AGT STABW1
STABW2 STAGI STAGT STATHR STPGA1
annex_a annex_b bcmalloc bcmalloc_numSizes
board_rev bt_master_enable clear_device cm_1024qam
cm_20_clipping cm_45 cm_45i cm_aboard_v2 cm_aboard_v3
cm_adv_map_runahead cm_amp cm_annex cm_cboard
cm_clc cm_ds_ref_freq cm_iboard_v1a cm_iboard_v1b cm_phy_ref_freq
cm_sboard cm_tuner cm_upstream_priority_queue_support
cm_us_ref_freq cm_us_sample_freq defaults del_extra_data
eth_autoneg eth_duplex_full eth_reject_cam eth_speed {flush}
high_output_pa hpna_message_level interfaces
local_bt_mac_address mac_address manufactured
power_save_enable read remote_bt_mac_address
scdma_code_matrix shack_tries show spreader_scale
stats tftp_read tftp_write usb_device_id usb_mac_address
usb_rndis usb_vendor_id wdog_enable wdog_timeout write
zone
----
------------------------------------------------------------------------------
Command Table: CM Propane NonVol Commands (propane)
Description:
Commands to show/change the CM Propane NonVol settings.
Available Commands:
clear_device defaults del_extra_data enable_propane {flush}
manufactured read show stats tftp_read
tftp_write timer write
----
------------------------------------------------------------------------------
Command Table: CM SNMP NonVol Commands (snmp_cm)
Description:
Commands to show/change the SNMP NonVol settings.
Available Commands:
allow_config clear_device defaults del_extra_data
diag_disable_post_reg dload_tries docsDevSerialNumber
docsDevSwAdminStatus docsDevSwCurrentVers
docsDevSwFilename docsDevSwOperStatus docsDevSwServer
{flush} hide_ipstack_ifentries ip_def_ignore llc_unm_ignore
manufactured max_dload_tries read show single_ip_filt
stats sysContact sysDescr sysLocation sysName
sysORDescr sysORID sysObjectId sysServices tftp_read
tftp_write vendor_name write
----
------------------------------------------------------------------------------
Command Table: DOCSIS CM Upstream Calibration NonVol Commands (us-cal)
Description:
Commands to show/change the DOCSIS CM Upstream Calibration NonVol settings.
Available Commands:
board_rev clear_device clear_table cm_amp config
control def_table defaults del_extra_data {flush}
manufactured offset print read show
stats tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: User Interface NonVol Commands (userif)
Description:
Commands to show/change the Message Log NonVol settings.
Available Commands:
clear_device defaults del_extra_data dhcp_settings fields
{flush} http_acl_host_add http_acl_host_remove
http_acl_hosts_clear http_admin http_adv_ipstacks
http_enable http_ipstacks http_password_idle_timeout
http_password_seed http_socket_show http_user
inactivity_timeout ip_stack_number manufactured password
read severities show ssh_enable ssh_ipstacks
stats telnet_enable telnet_ipstacks tftp_read tftp_write
user_name write
----
------------------------------------------------------------------------------
Command Table: Ping Commands (pingHelper)
Description:
Ping Helper Thread settings and commands. These commands allow you to set the
ping utility up with precise control over packet sizes, timeout values, etc.
Available Commands:
all_sizes end_size hs_nowait hs_wait ip_address
ip_stack ip_sweep number_of_pings ping
restore_defaults show_settings start_size stats
step_amount stop time_between_pings verbosity
verify_enable wait_enable wait_time
----
------------------------------------------------------------------------------
Command Table: SNMP Commands (snmp)
Description:
SNMP commands.
Available Commands:
agent_core_show cm_cfgfile cm_filter_test debug flush
get group_members install_group key_v3 log
n2m notify_setup parent_chain set severities
show test thread_info throttle trap
view_v1v2
----
------------------------------------------------------------------------------
Command Table: Snoop Commands (snoop)
Description:
Commands to show/change the state of Snoop objects.
Available Commands:
debug enable priority show
----
------------------------------------------------------------------------------
Command Table: USB HAL Commands (usb_hal)
Description:
Commands to show/change the USB HAL state.
Available Commands:
hal_show show
----
------------------------------------------------------------------------------
RE: haxorware webshell command - torro32 - 29-08-2012
(25-02-2012, 08:40 PM)drewmerc Wrote: which command? any in particular
------------------------------------------------------------------------------
Command Table: CM DOCSIS Commands (CM)
Description:
CM DOCSIS Commands
Available Commands:
con_high mbufShow memShow mutex_debug ping
read_memory reset routeShow run_app shell
stackShow taskDelete taskInfo taskPrioritySet taskResume
taskShow taskSuspend taskTrace usfsShow version
write_memory zone
----
Available sub-command tables:
[HeapManager] [cm_hal] [docsis_ctl] [embedded_target] [enet_hal] [event_log]
[flash] [forwarder] [ip_hal] [msgLog] [non-vol] [pingHelper] [snmp] [snoop]
[usb_hal]
------------------------------------------------------------------------------
Command Table: HeapManager Commands (HeapManager)
Description:
Broadcom Heap Manager (malloc/free) settings and commands.
Available Commands:
bcheck bcheck_crash bcheck_enable last_error maxAlloc
memShow stats threadUsage trace walk
walk_alloc
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS HAL Commands (cm_hal)
Description:
Commands to show/change the CM DOCSIS HAL state.
Available Commands:
ackcel_show bcmalloc_show bist_test change counters
cpe_add cpe_del cpe_max cpe_print ds_state
hal_show l2vpn_mask ldaix_read lock_ds log
mac_diag map_lead_time_show packets_queued qam_lock
qosParms read_mbr read_posted scan_ds scan_stop
set_mode show show_halif transmit tune
tune_band tuner_read tuner_write us_burst us_cw_transmit
us_debug us_reset us_sweep us_transmit write_mbr
write_posted
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS Control Thread Commands (docsis_ctl)
Description:
Commands to change the state of the DOCSIS Control thread.
Available Commands:
ClearCmCert binarySfid bpiShow cfg_hex_show cfg_tlv_show
clear_image comp_mac_to_phy comp_phy_to_mac copy_image dload
dsdiag dsx_show goto_ds goto_us igmpShow
ip_initialize ip_show l2vpn_show log_messages map_debug
modem_caps rate_shaping_enable rng_rsp scan_stop
showFlows state stop_download ucdShow ucddiag
up_dis us_phy_oh_show usdiag
----
Available sub-command tables:
[dsxTest] [propane_ctl]
------------------------------------------------------------------------------
Command Table: Dynamic Service Test Command Table (dsxTest)
Description:
Commands to test dynamic service.
Available Commands:
addConfigFile autoDsxTest changeConfigFile delRef
delSfids dropDsxMsg dscLocal dsdLocal show
----
------------------------------------------------------------------------------
Command Table: CM Propane Control Thread Commands (propane_ctl)
Description:
Commands to change the state of the Propane Control thread.
Available Commands:
debug discovery dsx_complete oper_caps port_number
psi_grant release_psis request_psis show simulate
----
------------------------------------------------------------------------------
Command Table: Embedded Target Commands (embedded_target)
Description:
Commands to control the embedded target platform.
Available Commands:
bcmalloc_show bcmalloc_walk cache_test cp0_read cp0_write
dcache icache sdram_test start_perf_counters
stop_perf_counters test_bcmalloc
----
------------------------------------------------------------------------------
Command Table: Ethernet HAL Commands (enet_hal)
Description:
Commands to show/change the Ethernet HAL state.
Available Commands:
autoneg force_link full_duplex hal_show read_mii
show speed transmit write_mii
----
------------------------------------------------------------------------------
Command Table: Event Log commands (event_log)
Description:
Commands to manipulate the Event Log
Available Commands:
control flush log_event read show
silent stop_stress stress syslog verbose_show
----
------------------------------------------------------------------------------
Command Table: Flash Driver Commands (flash)
Description:
Commands to control the flash device driver.
Available Commands:
autoTest cfi_show close configRegion deinit
erase init open read readDirect
show write writeArray
----
------------------------------------------------------------------------------
Command Table: Forwarder Commands (forwarder)
Description:
Commands to show/change the Forwarder state.
Available Commands:
filter_logging_enable filter_logging_show halif_show
ip_filter_logging log_packets lt_add lt_clear
lt_delete lt_max_entries lt_show mac_filter_logging
port_filter_logging proto_filter_logging show
----
------------------------------------------------------------------------------
Command Table: IP Stack HAL Commands (ip_hal)
Description:
Commands to manage IP stacks and related tasks.
Available Commands:
bootloader clientif_debug dhcpc_debug dhcpc_show dload
hal_show ip_addr_show ipconfig kill_remote_dhcp_server
lease_show show test
----
------------------------------------------------------------------------------
Command Table: Message Log Settings Commands (msgLog)
Description:
Commands for changing Message Log Settings. These commands allow you enable
and disable display fields and severity levels for individual objects or for
groups of objects.
Available Commands:
fields severities show_settings
----
------------------------------------------------------------------------------
Command Table: Non-Volatile Settings Commands (non-vol)
Description:
Commands to change the non-volatile settings for the application.
Available Commands:
clear_device defaults del_extra_data flush manufactured
read show stats tftp_read tftp_write
write
----
Available sub-command tables:
[Motorola] [bfcApp] [bpi] [docsis] [ds-cal] [event_log] [factory] [halif]
[propane] [snmp_cm] [us-cal] [userif]
------------------------------------------------------------------------------
Command Table: CM Motorola NonVol Commands (Motorola)
Description:
Commands to show/change the CM Vendor (Motorola) NonVol settings.
Available Commands:
clear_device cli_enable cm_amp cm_hwrev cm_tuner
defaults del_extra_data dhcp_enable {flush} html_ro_enable
manufactured read rg_enable show stats
tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: BFC Application Settings Commands (bfcApp)
Description:
Commands to change the non-volatile settings for the BFC Application.
Available Commands:
auto_console clear_device console_stop_prompt defaults
del_extra_data driver_init_prompt {flush} manufactured
read serial_console show stats tftp_read
tftp_write write
----
------------------------------------------------------------------------------
Command Table: CM BPI NonVol Commands (bpi)
Description:
Commands to show/change the CM BPI NonVol settings.
Available Commands:
change_key clear_device code_access cvc_access defaults
del_extra_data {flush} key_location manufactured print
read show stats tftp_read tftp_write
write
----
------------------------------------------------------------------------------
Command Table: CM DOCSIS NonVol Commands (docsis)
Description:
Commands to show/change the CM DOCSIS NonVol settings.
Available Commands:
bpi_version clear_device concat_thresh defaults del_extra_data
dhcp_settings doc10_mcastpromisc ds_frequency enable
fake_reg {flush} ip_stack_number manufactured max_concat
queues rate_shaping_time read rng_class
rng_class_extension show startup_context startup_dsfreq
startup_uschan stats tftp_read tftp_timeout tftp_write
timer_disable ugs_depth ugs_table_entries us_channel
us_power write
----
------------------------------------------------------------------------------
Command Table: DOCSIS CM Downstream Calibration NonVol Commands (ds-cal)
Description:
Commands to show/change the DOCSIS CM Downstream Calibration NonVol settings.
Available Commands:
clear_device clear_tables coef defaults del_extra_data
{flush} frequency ldaix_time manufactured master
num_coef num_freq num_ldaix offset read
show stats tftp_read tftp_write tuner_step
write
----
------------------------------------------------------------------------------
Command Table: DOCSIS EventLog NonVol Commands (event_log)
Description:
Commands to show/change the DOCSIS EventLog NonVol settings.
Available Commands:
clear_device clear_event defaults del_extra_data event
{flush} manufactured read show stats
tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: Factory NonVol Commands (factory)
Description:
Commands to show/change the Factory NonVol settings.
Available Commands:
clear_device defaults del_extra_data {flush} key
manufactured read scratch_pad show sn
stats tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: HalIf NonVol Commands (halif)
Description:
Commands to show/change the HalIf NonVol settings.
Available Commands:
3420_optimized_map DS_AGI DS_AGT STABW1
STABW2 STAGI STAGT STATHR STPGA1
annex_a annex_b bcmalloc bcmalloc_numSizes
board_rev bt_master_enable clear_device cm_1024qam
cm_20_clipping cm_45 cm_45i cm_aboard_v2 cm_aboard_v3
cm_adv_map_runahead cm_amp cm_annex cm_cboard
cm_clc cm_ds_ref_freq cm_iboard_v1a cm_iboard_v1b cm_phy_ref_freq
cm_sboard cm_tuner cm_upstream_priority_queue_support
cm_us_ref_freq cm_us_sample_freq defaults del_extra_data
eth_autoneg eth_duplex_full eth_reject_cam eth_speed {flush}
high_output_pa hpna_message_level interfaces
local_bt_mac_address mac_address manufactured
power_save_enable read remote_bt_mac_address
scdma_code_matrix shack_tries show spreader_scale
stats tftp_read tftp_write usb_device_id usb_mac_address
usb_rndis usb_vendor_id wdog_enable wdog_timeout write
zone
----
------------------------------------------------------------------------------
Command Table: CM Propane NonVol Commands (propane)
Description:
Commands to show/change the CM Propane NonVol settings.
Available Commands:
clear_device defaults del_extra_data enable_propane {flush}
manufactured read show stats tftp_read
tftp_write timer write
----
------------------------------------------------------------------------------
Command Table: CM SNMP NonVol Commands (snmp_cm)
Description:
Commands to show/change the SNMP NonVol settings.
Available Commands:
allow_config clear_device defaults del_extra_data
diag_disable_post_reg dload_tries docsDevSerialNumber
docsDevSwAdminStatus docsDevSwCurrentVers
docsDevSwFilename docsDevSwOperStatus docsDevSwServer
{flush} hide_ipstack_ifentries ip_def_ignore llc_unm_ignore
manufactured max_dload_tries read show single_ip_filt
stats sysContact sysDescr sysLocation sysName
sysORDescr sysORID sysObjectId sysServices tftp_read
tftp_write vendor_name write
----
------------------------------------------------------------------------------
Command Table: DOCSIS CM Upstream Calibration NonVol Commands (us-cal)
Description:
Commands to show/change the DOCSIS CM Upstream Calibration NonVol settings.
Available Commands:
board_rev clear_device clear_table cm_amp config
control def_table defaults del_extra_data {flush}
manufactured offset print read show
stats tftp_read tftp_write write
----
------------------------------------------------------------------------------
Command Table: User Interface NonVol Commands (userif)
Description:
Commands to show/change the Message Log NonVol settings.
Available Commands:
clear_device defaults del_extra_data dhcp_settings fields
{flush} http_acl_host_add http_acl_host_remove
http_acl_hosts_clear http_admin http_adv_ipstacks
http_enable http_ipstacks http_password_idle_timeout
http_password_seed http_socket_show http_user
inactivity_timeout ip_stack_number manufactured password
read severities show ssh_enable ssh_ipstacks
stats telnet_enable telnet_ipstacks tftp_read tftp_write
user_name write
----
------------------------------------------------------------------------------
Command Table: Ping Commands (pingHelper)
Description:
Ping Helper Thread settings and commands. These commands allow you to set the
ping utility up with precise control over packet sizes, timeout values, etc.
Available Commands:
all_sizes end_size hs_nowait hs_wait ip_address
ip_stack ip_sweep number_of_pings ping
restore_defaults show_settings start_size stats
step_amount stop time_between_pings verbosity
verify_enable wait_enable wait_time
----
------------------------------------------------------------------------------
Command Table: SNMP Commands (snmp)
Description:
SNMP commands.
Available Commands:
agent_core_show cm_cfgfile cm_filter_test debug flush
get group_members install_group key_v3 log
n2m notify_setup parent_chain set severities
show test thread_info throttle trap
view_v1v2
----
------------------------------------------------------------------------------
Command Table: Snoop Commands (snoop)
Description:
Commands to show/change the state of Snoop objects.
Available Commands:
debug enable priority show
----
------------------------------------------------------------------------------
Command Table: USB HAL Commands (usb_hal)
Description:
Commands to show/change the USB HAL state.
Available Commands:
hal_show show
----
------------------------------------------------------------------------------
worth of gold!!!
RE: haxorware webshell command - southernyankey1970 - 29-08-2012
drew rocks!
Ask and you shall receive...
RE: haxorware webshell command - SlowGrind6 - 29-08-2012
Here are a few more things that might help someone out...
DESCRIPTION: explained below
Shows usage information about the specified command(s), or lists the set of
commands available in the active table. If no parameters are specified, then
an abbreviated list of all commands and subtables is displayed.
-t -- Shows the entire tree of command tables and commands (in
abbreviated form).
-l -- Shows detailed information about all commands and subtables (this
can print a LOT of information)!
-s -- Shows detailed information on just the subtables.
-i -- Shows detailed information on just the registered instances for
the active table.
-a -- Does everything that the -l, -s, and -i options do.
Command is the name (or partial name) of one or more commands and subtables
for which you want detailed help to be displayed.
EXAMPLES:
help -- This shows an abbreviated list of all commands and
subtables.
help cd -- This shows detailed help on the 'cd' command.
help cd ! diag -- This shows detailed help on the 2 commands and subtable
listed.
help -l -- Shows detailed help on all available commands and
subtables.
---------------------------------------------------------------------------
CM> help
CM>
CM> help -t
CM> help -t
Command Table: Built-in Commands (built-in)
Description:
System-wide, built-in commands that are handled by the Console Thread. These
commands are always available, regardless of which command table is active.
Available Commands:
! ? REM cd dir
find_command help history instances ls
man pwd sleep syntax system_time
usage
----
RE: haxorware webshell command - Canis-Major - 06-07-2015
Dont login to telnet twice lol.. your prob using webshell AND telnet if you aint using two telnet login's..
RE: haxorware webshell command - drewmerc - 06-07-2015
dont even have any of the hax web pages open
RE: haxorware webshell command - Canis-Major - 06-07-2015
webgui was always buggy for me, prob cause i prefer the diag full.. hence how I learnt serial.. now if they had a fluid webgui for telnet, I mighta went a different way..