04-06-2009, 09:54 PM
hi am new to this forum and am having a few problems trying to set it up ,have tried everything i have read and still failing to get a connection and was hoping someone would be kind enuf to help me out of my prediacment , i have haxoware 1.1 rev 31 installed on my sb5101e modem
now i get confused
in overview i have this
Task Status
Acquire Downstream Channel Done
Obtain Upstream Parameters Done
Upstream Ranging Done
Establish IP Connectivity In Progress
Retrieve Time of Day Waiting
Negotiate security Waiting
Receive configuration Waiting
Register connection Waiting
Cable modem status Ranging Complete
signal i have this
Downstream
Frequency 331 MHz
Status Locked
Annex DOCSIS
Modulation QAM256
Symbol Rate 5360537 sym/sec
Receive Power 3.7 dBmV
Signal to Noise ratio 39.0 dB
Upstream
Frequency 34 MHz
Channel ID 3
Status Ready
Mode TDMA
Symbol Rate 2560000 sym/sec
Transmit Power 40.0 dBmV
i have tried to use dhcp sniffer , but not sure if i have to have the modem actually connected to the net before i use it? cos when i try to sniff i just get no bootloader macs found
it says region NONVOL an d the only files i have are
CM0014E8AC96B2.tar and nonvol.bin (32768 bytes)
my settings are such
General
Factory Mode
Disable Firmware Upgrades /
Force Network Access /
Tftp Enforce Bypass
Ignore Unknown Messages /
Disable IP Filters on startup
Administration
Control Panel IP Address 192.168.100.1
DHCP Server /
WebGUI
Password protection
Username root
Password *****
Telnet Server
Current state Running
Run on startup /
Username root
password *****
frequencys are
Annex docsis Plan european
Preferred DS Freq 1 331000000Hz
Preferred DS Freq 2 339000000Hz
Preferred DS Freq 3 330750000Hz
Upstream Channel 0
Addresses
HFC MAC 00:14:E8:AC:96
5
Ethernet MAC 00:14:E8:AC:96:B3
USB MAC 00:14:E8:AC:96:B3
Serial Number 140255606729998301021001
Certificate generation
Certificate type mtorola docsis
config file reads liek this
Force Config File
Server IP
File name cm-2148-256
Autoserve
Autoserve Config File (disabled)
Store new config
sorry for the long winding lots of extars thread , but its better to put everything down in the hope that sum1 can tell me what im doing wrong , as i keep having to drive around looking for hotspots to try and read what im doing wrong , but its very hard to do so , then run back home to try and read and also do , what i had previosuly read
many thanks in advance for any help
tween
or maybe there is a file i can upload and solve all my problems
also i see that there are 3 mac addresses hfc ,ethernet , and usb mac
what are all these for?
now i get confused
in overview i have this
Task Status
Acquire Downstream Channel Done
Obtain Upstream Parameters Done
Upstream Ranging Done
Establish IP Connectivity In Progress
Retrieve Time of Day Waiting
Negotiate security Waiting
Receive configuration Waiting
Register connection Waiting
Cable modem status Ranging Complete
signal i have this
Downstream
Frequency 331 MHz
Status Locked
Annex DOCSIS
Modulation QAM256
Symbol Rate 5360537 sym/sec
Receive Power 3.7 dBmV
Signal to Noise ratio 39.0 dB
Upstream
Frequency 34 MHz
Channel ID 3
Status Ready
Mode TDMA
Symbol Rate 2560000 sym/sec
Transmit Power 40.0 dBmV
i have tried to use dhcp sniffer , but not sure if i have to have the modem actually connected to the net before i use it? cos when i try to sniff i just get no bootloader macs found
it says region NONVOL an d the only files i have are
CM0014E8AC96B2.tar and nonvol.bin (32768 bytes)
my settings are such
General
Factory Mode
Disable Firmware Upgrades /
Force Network Access /
Tftp Enforce Bypass
Ignore Unknown Messages /
Disable IP Filters on startup
Administration
Control Panel IP Address 192.168.100.1
DHCP Server /
WebGUI
Password protection
Username root
Password *****
Telnet Server
Current state Running
Run on startup /
Username root
password *****
frequencys are
Annex docsis Plan european
Preferred DS Freq 1 331000000Hz
Preferred DS Freq 2 339000000Hz
Preferred DS Freq 3 330750000Hz
Upstream Channel 0
Addresses
HFC MAC 00:14:E8:AC:96
5 Ethernet MAC 00:14:E8:AC:96:B3
USB MAC 00:14:E8:AC:96:B3
Serial Number 140255606729998301021001
Certificate generation
Certificate type mtorola docsis
config file reads liek this
Force Config File
Server IP
File name cm-2148-256
Autoserve
Autoserve Config File (disabled)
Store new config
sorry for the long winding lots of extars thread , but its better to put everything down in the hope that sum1 can tell me what im doing wrong , as i keep having to drive around looking for hotspots to try and read what im doing wrong , but its very hard to do so , then run back home to try and read and also do , what i had previosuly read
many thanks in advance for any help
tween
or maybe there is a file i can upload and solve all my problems
also i see that there are 3 mac addresses hfc ,ethernet , and usb mac
what are all these for?