+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: DPC2100r2 Problems (/showthread.php?tid=1634)
Pages:
1
2
DPC2100r2 Problems - freebullets - 12-06-2012
I'm using a subscribed DPC2100r2 with Haxorware. For the past few months, internet has been dropping occasionally, and the modem needed a reset. For the past couple days, it's been dropping every 10 minutes, and I'm getting high pings. Log:
Code:
2012-06-12 08:15:52 Information B605.10 Map Reject - Downstream Traffic Flow Not Mapped to BPI+ SAID (EC=8)
2012-06-12 08:15:52 Information B601.0 SA Map State Machine Started
2012-06-12 08:14:59 Information I500.0 Registration Completed
2012-06-12 08:14:59 Information B401.0 Authorized
2012-06-12 08:14:58 Critical I402.0 TLV-11 - Illegal Set operation failed
2012-06-12 08:14:58 Information D507.0 Retrieved Time....... SUCCESS
2012-06-12 08:14:55 Information D509.0 Retrieved TFTP Config bpr[snip] SUCCESS
1970-01-01 00:00:36 Error D004.3 ToD request sent- No Response received
1970-01-01 00:00:35 Information D511.0 Retrieved DHCP .......... SUCCESS
1970-01-01 00:00:31 Critical D003.0 DHCP WARNING - Non-critical field invalid in response.
1970-01-01 00:00:27 Information T500.0 Acquired Upstream .......... SUCCESS
1970-01-01 00:00:13 Critical R002.0 No Ranging Response received - T3 time-out (US 2)
1970-01-01 00:00:10 Information T501.0 Acquired Downstream (591000000 Hz)........ SUCCESS
1970-01-01 00:00:05 Notice M571.1 Ethernet link up - ready to pass packets
2012-06-12 08:14:10 Notice M573.0 Modem Is Shutting Down and Rebooting...
2012-06-12 08:14:09 Critical Resetting the cable modem due to docsDevResetNowI don't remember seeing the TLV-11 message until now. From this thread, I take it that's my issue? What does the error mean, and how can I fix it? Is the stock firmware for my modem available for download somewhere? I forgot to back mine up when I installed Haxorware a couple years ago.
RE: DPC2100r2 Problems - ABMJR - 12-06-2012
Are you ignoring any "T" timeouts? what is the signal level? Is this the Lite or Diag version? Your ISP can see Haxorware as it does occupy a small area of Mapped mem
RE: DPC2100r2 Problems - freebullets - 12-06-2012
(12-06-2012, 03:40 PM)ABMJR Wrote: Are you ignoring any "T" timeouts?Nope. The T3 is the only one I usually get.
(12-06-2012, 03:40 PM)ABMJR Wrote: what is the signal level?Down: -3.9 dBmV
SNR: 36.2 dB
Up: 47.4 dBmV
(12-06-2012, 03:40 PM)ABMJR Wrote: Is this the Lite or Diag version?The main one from the front page.
(12-06-2012, 03:40 PM)ABMJR Wrote: Your ISP can see Haxorware as it does occupy a small area of Mapped memHow much would my ISP care about me using stock Haxorware?
RE: DPC2100r2 Problems - ABMJR - 12-06-2012
Is it the Lite or DIAG version of Haxorware?
Do you have firmware updates checked to be disabled? Looks like a another TLV-11 issue, which could be a bad CVC from your ISP
RE: DPC2100r2 Problems - freebullets - 12-06-2012
(12-06-2012, 04:56 PM)ABMJR Wrote: Is it the Lite or DIAG version of Haxorware?
Do you have firmware updates checked to be disabled? Looks like a another TLV-11 issue, which could be a bad CVC from your ISP
It says, "This firmware contains 145470 bytes of compiled custom CODE, and was built on Thu Nov 12 14:37:44 2009." So, it's the DIAG version.
I've had the Disable Firmware Updates checkbox checked, but I'm not sure if it's ever been left unchecked. What does CVC stand for?
EDIT: BTW, I called Charter today, and they said they couldn't communicate with my modem.
RE: DPC2100r2 Problems - ABMJR - 12-06-2012
You have SNP disabled after registration checked AND you may heave redirected the port to something else..
RE: DPC2100r2 Problems - freebullets - 12-06-2012
(12-06-2012, 06:34 PM)ABMJR Wrote: You have SNP disabled after registration checked AND you may heave redirected the port to something else..
Disable SNMP Agent after registration is checked and Redirect SNMP Traps is unchecked.
Do you know how to fix my issue? I can't do anything with my internet shutting down every 10 minutes.
RE: DPC2100r2 Problems - ABMJR - 12-06-2012
remove the check from Disable SNMP Agent after registration
I would allow firmware updates...
Why you would have Haxorware on a SUBBED MODEM IS BEYOND ME..And its the Diag version which uses some of image1 memory...
Read as I think you have no clue what the hell you are doing
RE: DPC2100r2 Problems - freebullets - 12-06-2012
(12-06-2012, 07:19 PM)ABMJR Wrote: Why you would have Haxorware on a SUBBED MODEM IS BEYOND ME..And its the Diag version which uses some of image1 memory...I think that's a bit irrelevant, but since you asked, I installed it to gain new knowledge and mess around with my modem.
(12-06-2012, 07:19 PM)ABMJR Wrote: Read as I think you have no clue what the hell you are doingThanks?
"You didn't upload a valid firmware image. No changes have been made"
I'm getting that error when I try flashing the original firmware. Can I not do this through the web UI?
Edit: Restored default settings and flashed the lite version. Up to 42 minutes so far...
RE: DPC2100r2 Problems - freebullets - 13-06-2012
One of those 2 things fixed my internet dropping issue, but I'm still getting like 500-1000ms ping times. How can I restore the stock firmware?