+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: SB5101E firmware questions (/showthread.php?tid=1824)
RE: SB5101E firmware questions - drewmerc - 06-08-2012
it maybe the old version of haxor i dumped? it was pre 1.1 so it's 5101 diag based(not lite) i guess at some point i'll need to dump a 5102 diag version
RE: SB5101E firmware questions - coldfusion - 06-08-2012
Im running 1.1 rev39-diag, in software version it shows SB5101-2.7.6.0-GA-00-NOSH. I actually reflashed last night to make sure I was running DIAG, I wonder why those commands are not in the final version, is it possible to downgrade to previous version of haxo from the webgui?
RE: SB5101E firmware questions - SlowGrind6 - 06-08-2012
You should be able to use the command.....man....
And here is a link to several more commands. Hopes this helps you out.
http://www.pastebay.net/1066103
RE: SB5101E firmware questions - coldfusion - 06-08-2012
(06-08-2012, 04:30 AM)SlowGrind6 Wrote: You should be able to use the command.....man....
And here is a link to several more commands. Hopes this helps you out.
http://www.pastebay.net/1066103
Thanks for those SlowGrind6, yeah I should be able to use them, but for some weird reason they say they are not supported, cheers.
RE: SB5101E firmware questions - biglove69 - 01-11-2012
Specified subtable ('snmp') doesn't exist! Can't change to it...
Active Command Table: Non-Volatile Settings Commands (non-vol)
what do i need to fix on my modem
RE: SB5101E firmware questions - SlowGrind6 - 02-11-2012
You can always try the search command: find_command
And this is only for diag version of hax.
RE: SB5101E firmware questions - Rickz - 14-11-2012
i believe this is a bug with haxor.. my isp don't disable telnet. and after registration telnet still is active, so registered with isp or not most commands are not there(directorys like snmp, non-vol and their commands are missing) i even flashed new virgin full flash for chipset intel which has my 5101 and the flashed fresh firm rev 39 diag or lite not matter both has same issue. i'm unable to run commands such as:
--------------------------------
stealth snmp settings
--------------------------------
cd /n/s
max_dload_tries 0
hide_ipstack_ifentries true
docsDevSwAdminStatus 3
docsDevSwOperStatus 2
diag_disable_post_reg true
write
-----------------------------------------
diable external telnet access
-----------------------------------------
cd /n/m
telnet_ipstacks 2
write
--------------------------------
disable ToD time of day requests
cd /non/docsis
enable tod false
write
cd /
reset
Disable SNMP Agent after registration
cd n/s
diag_disable_post_reg true
write
increases detail level of event log.
cd /s
set cmConfigEnableAllEventLogPriorities int 1
(yes)
cd /n
write
prevent US blacklisting at the CMTS
cd /s
set cmConfigT3TimeoutInitRngRetries int 5
(yes)
cd /n
write
(disable remote telnet)
cd non-vol
cd msg-log
telnet_ipstacks 2
(block all remote updates)
cd /
cd non-vol
cd snmp
max_dload_tries 0
write
(hide your ip)
cd non-vol
cd snmp
hide_ipstack_ifentries true
write
Disable SNMP filters (filters that provider sets to restrict ports and IP ranges use):
cd /s
cm_filters off
cd /n
write
Disables reading the modem with snmp commands.
cd /
cd snmp
view_v1v2 Noaccess
y
cd
someone told me to enable factory mode for running those commands.. i actually have it enable from web interface.. still the issue persist..
i flashed Sigma RC1 for 5101(SB5101.SIGMAX2.130.RC1.bin) and i'm able to run all commands...
again i recommend to authors of haxor to check and confirm this issue.
also will be great if certs from SBG901/41 could be used with 5101 :-D
i'm asking too much?
for those who would like to run those commands use a shelled original firmware or the sigma one then reflash haxor on it.. i guess all changes will remain active there ?
maybe not.. if part of non-vol /snmp is erased are we really protected from ISP eyes ? since we can't use stealth options to hide..... this could be serious hole for hac_ked modems
some cuestions to answer... let's give a chance for the experts to respond about this.
My Best Regards
RE: SB5101E firmware questions - marcin888888 - 14-11-2012
im on the same boat
could some1 explain why the commands dont work!!!!!!!!!!!!
RE: SB5101E firmware questions - ABMJR - 14-11-2012
Your ISP disabled TELNET access to the commands you are looking to use after registration. Your ISP can see you ...
No, Stealth doesnt mean what it says...
Its all quite simple..
RE: SB5101E firmware questions - drewmerc - 14-11-2012
hiding your modem from the isp will make it stand out on the ctms,you want to blend into the crowd