+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: Ambit vmng 300 + 300 v2 (/showthread.php?tid=3625)
Pages:
1
2
RE: Ambit vmng 300 + 300 v2 - Canis-Major - 23-06-2015
I guess that depends on what I flash, cause so far, 3 full 8mb dump's from different site's are well fecked.. ie not working.. just goin through what I got before I desolder wires, but tell me, if I have an image1 and image2 from someone, which tabs do they go into, like, say I want sbh alpha 1.1 on this, done the bootloader, where do I chuck alpha, env1 or 2, or ubfi1 or 2?
RE: Ambit vmng 300 + 300 v2 - andy m - 23-06-2015
a300 a1.1 is alpha n 6120 bootloader
al catch up 2moz night
RE: Ambit vmng 300 + 300 v2 - Canis-Major - 24-06-2015
cheer's mate, was just reading usbjtag, who say if the nv is corrupted, no eth, some crap like that, I'll test these out, and get back, hopefully with positive result's, thanks
shame no matter what I flash, eth aint working, when it was.. could be cause serial wired up, doubtful though, ah well..
RE: Ambit vmng 300 + 300 v2 - andy m - 24-06-2015
ethernet should work use 000000000 ambit 300 a think tht is stock check if tht is your ethernet is working so flash alpha 1.1
good luck
RE: Ambit vmng 300 + 300 v2 - Canis-Major - 24-06-2015
It aint working across all flashes, used around 5 different 'backup's', though dunno if it's just disabled due to corrupt nvram, (most likely) and this ash/busybox is a mess compared to origional, it's like, um, yup? How to get eth back anyone, I must have asked in 5 posts now..?
I post a log:
Deleted previous log, thought it was better to post this, since in all firmware's, this in my opinion, would denote the actual problem:
Ingress Hook on eth0
Dbridge Init SUCSESS
Autoconfiguration disabled for br0
HAL_MacDsUnicastDataFilterAdd: system_rev = 1
Autoconfiguration disabled for lbr0
HAL_MacDsUnicastDataFilterAdd: system_rev = 1
Autoconfiguration disabled for lan0
Autoconfiguration disabled for wan0
HAL_MacDsUnicastDataFilterAdd: system_rev = 1
Which appear's to be responsible for disabling the eth, I have tried multiple 8mb dump's, 2 which I know have good cert's etc, and no corrupted nvram's, yet no matter what I flash, I cannot get eth of modem to kick in, anyone?
Pleeease? Pretty pleease?
RE: Ambit vmng 300 + 300 v2 - daviddds - 29-06-2015
eth0 is the CPU internal interface I believe, if you reload the ORIGINAL stock dump, does it work?
RE: Ambit vmng 300 + 300 v2 - Canis-Major - 29-06-2015
No, can add forwarding tables etc, 127 etc is gone, I know about eth0 when adding forwarding tables etc, they are removed upon reboot, so no f'n good, relegated these to bricked at the mo, one defo used for spares, but with pin 1 + 2 now 3.3 volt's on the other, so no point repairing..