Thomson THG540 to SB5101 Haxorware

[icebreaker]

Hi mates.

I have a Thomson THG540 that i have received from my Cable Operator, i am paying for this service.

I have tried to use a Motorola SB5101 with Haxorware, and put everything from the Thomson THG540: MAC, Serial, Downstream Frequency, Upstream Channel and Spoof of Firmware Version.

The problem is that the Motorola SB5101 only gets to the SEND light blinking and go no further.

Any sugestions on this?


Thanks for your help.

[icebreaker]

Nobody?

[drewmerc]

saying it only gets to the send light flashing tells us nothing, try posting a telnet log

[icebreaker]

saying it only gets to the send light flashing tells us nothing, try posting a telnet log

Here it goes:

Haxorware integrated telnet daemon

Username: root
Password: *****
Welcome.

CM>
CM> Adjusting the initial ranging power to 21.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 52.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 39.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 27.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 14.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 55.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 49.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 42.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 36.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 30.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 24.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 17.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 11.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 58.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> 0x00022fba [CmDocsisCtlThread] BcmCmDocsisCtlThread::T3NoRngRspEvent: (CmDocsisCtlThread) ERROR - No initial ranging response from CMTS.
0x00022fba [CmDocsisCtlThread] BcmCmDocsisCtlThread::CommonRngErrorHandler: (CmDocsisCtlThread) reason: 8 (kMaxT3NoRngRspTimeouts)
0x00022fba [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextUsChan: (CmDocsisCtlThread)
0x00022fba [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
Logging event: No Ranging Response received - T3 time-out (US 5)
Logging event: Init RANGING Critical Ranging Request (17) Retries exhausted

CM> Selecting UCD for Us Channel 4

0x00023bfe [CmDocsisCtlThread] BcmCmDocsisCtlThread:sSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 8.0 dBmV
0x00023c12 [CmDocsisCtlThread] BcmCmDocsisCtlThread::RxMsgEvent: (CmDocsisCtlThread) WARNING - iteration limit reached. giving up control...
Not logging event ID 2307948724, control for level 7 is 0.

CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 46.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 21.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 52.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 39.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 27.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 14.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 55.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 49.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 42.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 36.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 30.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 24.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 17.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 11.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> Adjusting the initial ranging power to 58.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 4)

CM> 0x00049fd4 [CmDocsisCtlThread] BcmCmDocsisCtlThread::T3NoRngRspEvent: (CmDocsisCtlThread) ERROR - No initial ranging response from CMTS.
0x00049fd4 [CmDocsisCtlThread] BcmCmDocsisCtlThread::CommonRngErrorHandler: (CmDocsisCtlThread) reason: 8 (kMaxT3NoRngRspTimeouts)
0x00049fd4 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextUsChan: (CmDocsisCtlThread)
0x00049fd4 [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
Logging event: No Ranging Response received - T3 time-out (US 4)
Logging event: Init RANGING Critical Ranging Request (17) Retries exhausted

CM> Selecting UCD for Us Channel 6

0x0004abbe [CmDocsisCtlThread] BcmCmDocsisCtlThread:sSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 8.0 dBmV
Not logging event ID 2307948724, control for level 7 is 0.

CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 46.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 21.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 52.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 39.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 27.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 14.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 55.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 49.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 42.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 36.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 30.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 24.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 17.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 11.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> Adjusting the initial ranging power to 58.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 6)

CM> 0x0007446e [CmDocsisCtlThread] BcmCmDocsisCtlThread::T3NoRngRspEvent: (CmDocsisCtlThread) ERROR - No initial ranging response from CMTS.
0x0007446e [CmDocsisCtlThread] BcmCmDocsisCtlThread::CommonRngErrorHandler: (CmDocsisCtlThread) reason: 8 (kMaxT3NoRngRspTimeouts)
0x0007446e [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextUsChan: (CmDocsisCtlThread)
0x0007446e [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
Logging event: No Ranging Response received - T3 time-out (US 6)
Logging event: Init RANGING Critical Ranging Request (17) Retries exhausted

CM> Selecting UCD for Us Channel 7

0x00075206 [CmDocsisCtlThread] BcmCmDocsisCtlThread:sSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 8.0 dBmV
Not logging event ID 2307948724, control for level 7 is 0.

CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 46.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 21.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 52.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 39.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 27.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 14.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 55.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 49.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 42.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 36.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 30.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 24.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 17.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 11.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> Adjusting the initial ranging power to 58.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 7)

CM> 0x000a0c4e [CmDocsisCtlThread] BcmCmDocsisCtlThread::T3NoRngRspEvent: (CmDocsisCtlThread) ERROR - No initial ranging response from CMTS.
0x000a0c4e [CmDocsisCtlThread] BcmCmDocsisCtlThread::CommonRngErrorHandler: (CmDocsisCtlThread) reason: 8 (kMaxT3NoRngRspTimeouts)
0x000a0c4e [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextUsChan: (CmDocsisCtlThread)
0x000a0c4e [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
Logging event: No Ranging Response received - T3 time-out (US 7)
Logging event: Init RANGING Critical Ranging Request (17) Retries exhausted

CM> Selecting UCD for Us Channel 8

0x000a1784 [CmDocsisCtlThread] BcmCmDocsisCtlThread:sSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 8.0 dBmV
Not logging event ID 2307948724, control for level 7 is 0.

CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 46.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 21.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 52.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 39.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 27.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 14.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 55.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 49.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 42.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 36.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 30.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 24.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 17.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 11.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> Adjusting the initial ranging power to 58.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 8)

CM> 0x000c16b0 [CmDocsisCtlThread] BcmCmDocsisCtlThread::T3NoRngRspEvent: (CmDocsisCtlThread) ERROR - No initial ranging response from CMTS.
0x000c16b0 [CmDocsisCtlThread] BcmCmDocsisCtlThread::CommonRngErrorHandler: (CmDocsisCtlThread) reason: 8 (kMaxT3NoRngRspTimeouts)
0x000c16b0 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextUsChan: (CmDocsisCtlThread)
0x000c16b0 [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
Logging event: No Ranging Response received - T3 time-out (US 8)
Logging event: Init RANGING Critical Ranging Request (17) Retries exhausted

CM> Selecting UCD for Us Channel 1

0x000c21e6 [CmDocsisCtlThread] BcmCmDocsisCtlThread:sSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 8.0 dBmV
Not logging event ID 2307948724, control for level 7 is 0.

CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 46.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 21.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 52.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 39.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 27.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 14.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 55.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 49.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 42.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 36.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 30.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 24.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 17.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 11.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> Adjusting the initial ranging power to 58.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 1)

CM> 0x000e52c2 [CmDocsisCtlThread] BcmCmDocsisCtlThread::T3NoRngRspEvent: (CmDocsisCtlThread) ERROR - No initial ranging response from CMTS.
0x000e52c2 [CmDocsisCtlThread] BcmCmDocsisCtlThread::CommonRngErrorHandler: (CmDocsisCtlThread) reason: 8 (kMaxT3NoRngRspTimeouts)
0x000e52c2 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextUsChan: (CmDocsisCtlThread)
0x000e52c2 [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
Logging event: No Ranging Response received - T3 time-out (US 1)
Logging event: Init RANGING Critical Ranging Request (17) Retries exhausted

CM> Selecting UCD for Us Channel 2

0x000e5b0a [CmDocsisCtlThread] BcmCmDocsisCtlThread:sSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 8.0 dBmV
Not logging event ID 2307948724, control for level 7 is 0.

CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 46.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 21.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 52.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 39.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 27.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 14.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 55.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 49.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 42.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 36.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 30.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 24.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 17.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 11.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> Adjusting the initial ranging power to 58.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 2)

CM> 0x0010a450 [CmDocsisCtlThread] BcmCmDocsisCtlThread::T3NoRngRspEvent: (CmDocsisCtlThread) ERROR - No initial ranging response from CMTS.
0x0010a450 [CmDocsisCtlThread] BcmCmDocsisCtlThread::CommonRngErrorHandler: (CmDocsisCtlThread) reason: 8 (kMaxT3NoRngRspTimeouts)
0x0010a450 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextUsChan: (CmDocsisCtlThread)
0x0010a450 [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
Logging event: No Ranging Response received - T3 time-out (US 2)
Logging event: Init RANGING Critical Ranging Request (17) Retries exhausted

CM> Selecting UCD for Us Channel 3

0x0010b364 [CmDocsisCtlThread] BcmCmDocsisCtlThread:sSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 8.0 dBmV
0x0010b36e [CmDocsisCtlThread] BcmCmDocsisCtlThread::RxMsgEvent: (CmDocsisCtlThread) WARNING - iteration limit reached. giving up control...
Not logging event ID 2307948724, control for level 7 is 0.
Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 46.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 21.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 52.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 39.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 27.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 14.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 55.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 49.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 42.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 36.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 30.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 24.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 17.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 11.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> Adjusting the initial ranging power to 58.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 3)

CM> 0x00123d06 [CmDocsisCtlThread] BcmCmDocsisCtlThread::T3NoRngRspEvent: (CmDocsisCtlThread) ERROR - No initial ranging response from CMTS.
0x00123d06 [CmDocsisCtlThread] BcmCmDocsisCtlThread::CommonRngErrorHandler: (CmDocsisCtlThread) reason: 8 (kMaxT3NoRngRspTimeouts)
0x00123d06 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextUsChan: (CmDocsisCtlThread)
0x00123d06 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextUsChan: (CmDocsisCtlThread) All usable upstream chans tried. Target next ds.
0x00123d06 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TargetNextDsChan: (CmDocsisCtlThread)
Logging event: No Ranging Response received - T3 time-out (US 3)
Logging event: Init RANGING Critical Ranging Request (17) Retries exhausted
Deleting DOCSIS 1.0 CoS Settings for SID 0
0x00123dce [CmDocsisCtlThread] BcmDocsisCmHalIf:eleteAllServiceFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service Flows, along with associated Classifiers and PHS rules...
Stopping DHCP/ToD/TFTP (client requested)...
DefaultSnmpAgentClass::RestartPendingEvent for SB5102 CM Agent w/ BRCM Factory Support
SB5102 CM Agent w/ BRCM Factory Support resetting to default state.
SB5102 CM Agent w/ BRCM Factory Support destroying users...
Pausing trap thread
SB5102 CM Agent w/ BRCM Factory Support destroying notifies...
Resuming trap thread
SB5102 CM Agent w/ BRCM Factory Support destroying views...
SB5102 CM Agent w/ BRCM Factory Support sending deferred traps...
Done w/ deferred traps.
SB5102 CM Event Log w/ BRCM Factory Support sending deferred async messages...
Done w/ deferred msgs
SB5102 CM Agent w/ BRCM Factory Support defering traps.
SB5102 CM Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted
SB5102 CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisCpeView
Non-Vol Settings successfully written to the device.
0x00123de2 [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
0x00123de2 [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Downstream Channel scan stopped!
0x00123df6 [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Scanning for a Downstream Channel...

mot_scanList: Setting override freq @ 0
Go back to 1st favorite
Attempting Downstream FEC lock @ freq= 501000000 Hz, QAM64

CM> Found energy at frequency 501000000Hz! Publishing event kEventEnergyDetected...
Attempting Downstream FEC lock @ freq= 507000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 513000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 519000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 525000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 531000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 537000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 543000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 549000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 555000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 561000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 567000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 573000000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 579000000 Hz, QAM64
0x00125d4a [CmDocsisCtlThread] BcmCmDocsisCtlThread::StartUsInit: (CmDocsisCtlThread) Locked on the downstream. Waiting for UCDs...

******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 579000000 Hz
Carrier Offset = -166 Hz
Symbol rate = 6952000 sym/sec
SNR = 20 dB
QAM Mode = QAM64
Tuner AGC = 0xfff00000
IF AGC = 0x183a6439
Power Level = -12 dB
QAM = LOCKED
FEC = LOCKED
******************************************

0x00125e80 [CMHH] BcmDocsisCmHalIf::HandleStatusIndication: (DOCSIS CableModem HalIf) ERROR - FEC Lock lost! Status = 0
0x00125e80 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncRestartErrorEvent: (CmDocsisCtlThread) reason: 0 (kDsLockFail)
Logging event: Ds Lock Failed - Reinitialize MAC...
Deleting DOCSIS 1.0 CoS Settings for SID 0
0x00125f48 [CmDocsisCtlThread] BcmDocsisCmHalIf:eleteAllServiceFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service Flows, along with associated Classifiers and PHS rules...
Stopping DHCP/ToD/TFTP (client requested)...
DefaultSnmpAgentClass::RestartPendingEvent for SB5102 CM Agent w/ BRCM Factory Support
SB5102 CM Agent w/ BRCM Factory Support resetting to default state.
SB5102 CM Agent w/ BRCM Factory Support destroying users...
Pausing trap thread
SB5102 CM Agent w/ BRCM Factory Support destroying notifies...
Resuming trap thread
SB5102 CM Agent w/ BRCM Factory Support destroying views...
SB5102 CM Agent w/ BRCM Factory Support sending deferred traps...
Done w/ deferred traps.
SB5102 CM Event Log w/ BRCM Factory Support sending deferred async messages...
Done w/ deferred msgs
SB5102 CM Agent w/ BRCM Factory Support defering traps.
SB5102 CM Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted
SB5102 CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisCpeView
Non-Vol Settings successfully written to the device.
0x00125f5c [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
0x00125f5c [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Downstream Channel scan stopped!
0x00125f70 [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Scanning for a Downstream Channel...

mot_scanList: Setting override freq @ 434000000
Scanning DS Channel at 434000000 Hz... (Initial target freq)

CM> Found energy at frequency 434000000Hz! Publishing event kEventEnergyDetected...
0x00126196 [CmDocsisCtlThread] BcmCmDocsisCtlThread::StartUsInit: (CmDocsisCtlThread) Locked on the downstream. Waiting for UCDs...

******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 434000000 Hz
Carrier Offset = 1 Hz
Symbol rate = 6952000 sym/sec
SNR = 37 dB
QAM Mode = QAM256
Tuner AGC = 0xfff00000
IF AGC = 0x162e0418
Power Level = -3 dB
QAM = LOCKED
FEC = LOCKED
******************************************


CM> Selecting UCD for Us Channel 5

0x00126fce [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchDsTimeSync: (CmDocsisCtlThread) starting ds time sync acquisition...
0x00127244 [CmDocsisCtlThread] BcmCmDocsisCtlThread::RxMsgEvent: (CmDocsisCtlThread) WARNING - iteration limit reached. giving up control...
0x00127262 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) downstream time sync acquired...
0x00127262 [CmDocsisCtlThread] BcmCmDocsisCtlThread:sSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 8.0 dBmV
0x00127262 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) rx unexpected kDsSyncOk indication...
Not logging event ID 2307948724, control for level 7 is 0.

CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 46.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 21.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 52.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

CM> Adjusting the initial ranging power to 39.0 dBmV...
Logging event: No Ranging Response received - T3 time-out (US 5)

---

It keeps trying to lock the Upstream, but it dosen´t.

[Fred_Watkins]

A 20 dB SNR is way too low....improve your cable plant connectors/splitters/ground block

[icebreaker]

A 20 dB SNR is way too low....improve your cable plant connectors/splitters/ground block

My signal, cable and connectors are fine.
That is just the Ranging finding a good frequency.

That is not the problem.

Any more sugestions?

[Winston]

Have you accessed the hardware?