30-11-2009, 10:54 PM
(This post was last modified: 02-12-2009, 05:28 PM by justsomeguy.)
hello again everyone...i've finally tried to program my sb5101...here's the steps that i've done so far..by the way i am using UJmodem to program it because usbjagnt doesn't ever detect the modem and UJmodem detected it right away..
1. read & then verify and also saved the bin
2. load haxorware11rev38-DIAG.bin
3.write & then verify
4. unplug modem and plug back in. (only 1 light came on)
5. opened new web browser and tried going on http://192.168.100.1/bpi.html
this is where i'm kinda stuck..my browser gave me a load page error. now a couple things here i'm not sure about...in the ujmodem program i had to keep the range at "all"...when i tried to pull up image0 or image1 it wouldn't let me load the haxorware into the program. gave me some kinda error about the size.... so i just wrote all...did i screw that part up???? the options it gave me in the range were : boot, cfg, image0, image1, log, all .......now there is also a certificate button where i can insert or save..i didn't do anything with that..also there was a place for serial and factory MIB..both of which i left empty.... now when i go to the interface page do i have to plug the coax into the box? or just the comp into the box? i haven't plugged it into the coax line yet..just into the computer and it gave me the page load error..and the hole time i've just had 1 light on the modem which is the 2nd light which says ACT beneth it (right beside the standby light)...
any help on my next steps would be greatly appreciated..sorry if i've been long winded or if there's not enough info either..but this is my first attempt at this and am a total virgin...
thanks everyone
justsomeguy
**ok so i'm gonna assume that i bricked this damn thing..lol...so i've found a couple threads on debricking this unit. but is there anybody who is familiar with UJmodem interface that can help me out? i'm thinking that i screwed up when i wrote to the boot..so anyone who knows this program can help a fellow out??
1. read & then verify and also saved the bin
2. load haxorware11rev38-DIAG.bin
3.write & then verify
4. unplug modem and plug back in. (only 1 light came on)
5. opened new web browser and tried going on http://192.168.100.1/bpi.html
this is where i'm kinda stuck..my browser gave me a load page error. now a couple things here i'm not sure about...in the ujmodem program i had to keep the range at "all"...when i tried to pull up image0 or image1 it wouldn't let me load the haxorware into the program. gave me some kinda error about the size.... so i just wrote all...did i screw that part up???? the options it gave me in the range were : boot, cfg, image0, image1, log, all .......now there is also a certificate button where i can insert or save..i didn't do anything with that..also there was a place for serial and factory MIB..both of which i left empty.... now when i go to the interface page do i have to plug the coax into the box? or just the comp into the box? i haven't plugged it into the coax line yet..just into the computer and it gave me the page load error..and the hole time i've just had 1 light on the modem which is the 2nd light which says ACT beneth it (right beside the standby light)...
any help on my next steps would be greatly appreciated..sorry if i've been long winded or if there's not enough info either..but this is my first attempt at this and am a total virgin...
thanks everyone
justsomeguy
**ok so i'm gonna assume that i bricked this damn thing..lol...so i've found a couple threads on debricking this unit. but is there anybody who is familiar with UJmodem interface that can help me out? i'm thinking that i screwed up when i wrote to the boot..so anyone who knows this program can help a fellow out??
