Pantheon
Thanx for sharring
I had version 220. works perfectly.
BlackCat Usb is best investment I have ever made in my life.
High quality software.
I do not buy to this BS badmouthing BC software and BC jtag.
The only problem with that I had, that dealer, who sold to me, sent to me 16 inch ribbon cable with that.
Reading and writing with that was not reliable, had to hold with finger and press while downloading, then I bought the pogo pins,so I do not have to solder in anything or hold with my finger.
I have red on other forum, that ribbon cable has to be less than 10 cm (6 inches) and every second line tied together and hooked to good ground , pin 10, on the modem. Just to isolate and prevent 'talking' between lines during transmission.
Pins 2,4,6,8 are going to nowhere
So I have made my own cable, and now is working like a champ, every time like a clockwork, no errors.
Debricked quite a few modems, it is snap, less than 2 min.
Software is easiest to use it, comparing to others, I've use before pararel BC jtag, SBH, and NT, Tom/UD, and BC is really shining , its a high quality software.
Whoever designed it, definitely he knows how to do it and he made fantastic job.
It is not any hodge-podge utility like SBH or NT, it is high quality soft.
Even newbee can use it with ease.
It is my best money spent I ever had made in my life.
And speed ????? PTFFFFFF
I do not care if it is 2 min, NT and SBH are doing that within 20 seconds
But BC USB is doing this reliable, and reliability is most important to me.
@Latency
"If your modem is bricked, use a PJtag and use Toms Utility."
No u do not have to use it.
BlackCat USB soft has two files in it , just for debricking the modems.
One for 5100 and one for 5101 and same for the boots.
It is snap to debrick now with BC USB.
Those files are in special folder, at least in the version 220 and previous.
Thanx for sharring
I had version 220. works perfectly.
BlackCat Usb is best investment I have ever made in my life.
High quality software.
I do not buy to this BS badmouthing BC software and BC jtag.
The only problem with that I had, that dealer, who sold to me, sent to me 16 inch ribbon cable with that.
Reading and writing with that was not reliable, had to hold with finger and press while downloading, then I bought the pogo pins,so I do not have to solder in anything or hold with my finger.
I have red on other forum, that ribbon cable has to be less than 10 cm (6 inches) and every second line tied together and hooked to good ground , pin 10, on the modem. Just to isolate and prevent 'talking' between lines during transmission.
Pins 2,4,6,8 are going to nowhere
So I have made my own cable, and now is working like a champ, every time like a clockwork, no errors.
Debricked quite a few modems, it is snap, less than 2 min.
Software is easiest to use it, comparing to others, I've use before pararel BC jtag, SBH, and NT, Tom/UD, and BC is really shining , its a high quality software.
Whoever designed it, definitely he knows how to do it and he made fantastic job.
It is not any hodge-podge utility like SBH or NT, it is high quality soft.
Even newbee can use it with ease.
It is my best money spent I ever had made in my life.
And speed ????? PTFFFFFF
I do not care if it is 2 min, NT and SBH are doing that within 20 seconds
But BC USB is doing this reliable, and reliability is most important to me.
@Latency
"If your modem is bricked, use a PJtag and use Toms Utility."
No u do not have to use it.
BlackCat USB soft has two files in it , just for debricking the modems.
One for 5100 and one for 5101 and same for the boots.
It is snap to debrick now with BC USB.
Those files are in special folder, at least in the version 220 and previous.