17-08-2010, 04:24 PM
I need a little help.
have read a lot of guides and followed them. this is how i have my max232 adaptor and ambit 255 modem.
![[Image: image0012c.jpg]](http://img444.imageshack.us/img444/2998/image0012c.jpg)
And this is the output i get from hyperterminal/putty.
i don't get any of the searching for frequecny like in the guides and videos.
have read a lot of guides and followed them. this is how i have my max232 adaptor and ambit 255 modem.
And this is the output i get from hyperterminal/putty.
i don't get any of the searching for frequecny like in the guides and videos.
Code:
Control: 0005
Major Rev: 0000
Minor Rev: 0000
Build Time: 2009/3/6 08:54:53 Z
File Length: 935469 bytes
Load Address: 80010000
Filename: ecram_sto.bin
HCS: a64f
CRC: 8c35e82b
Performing CRC on Image 2...
Detected LZMA compressed image... decompressing...
Target Address: 0x80010000
..............
Decompressed length: 3670227
Executing Image 2...
eCos - hal_diag_init
Init device '/dev/ttydiag'
Init tty channel: 8035d1e0
Init device '/dev/tty0'
Init tty channel: 8035d200
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: 0.2
Set output buffer - buf: 80391af0 len: 2048
Set input buffer - buf: 803922f0 len: 2048
BCM 33XX SERIAL config
Current Boot Image : 2
file length= 935469
program header length :92
Flash driver opened.
Total Parse 25 element
ParseTLV Successd !
Reading Permanent settings from non-vol...
Checksum for permanent settings: 0x74a5028e
*
*
* One or more of the settings groups was upgraded.
*
*
Settings were read and verified.
Reading Dynamic settings from non-vol...
Checksum for dynamic settings: 0x6f50a5b6
Settings were read and verified.
boot loader version = 3164
Tag : 11, Length : 1, Value =1
Tag : 12, Length : 1, Value =1
Tag : 13, Length : 1, Value =1
Tag : 14, Length : 1, Value =0
Tag : 15, Length : 1, Value =0
Tag : 16, Length : 1, Value =0
Tag : 17, Length : 1, Value =0
Tag : 18, Length : 1, Value =1
Tag : 19, Length : 1, Value =1
Tag : 1a, Length : 1, Value =1
Tag : 1b, Length : 1, Value =0
Tag : 1c, Length : 1, Value =0
Tag : 1d, Length : 1, Value =0
Tag : 1e, Length : 1, Value =0
Tag : 29, Length : 1, Value =1
Tag : 2d, Length : 1, Value =3
Tag : 64, Length : 120, Value =41 4d 42 49 54 20 45 75 72 6f 20 44 4f 43 53 4 9 53 20 32 2e 30 20 43 61 62 6c 65 20 4d 6f 64 65 6d 20 3c 3c 48 57 5f 52 45 56 3a 20 31 2e 31 39 3b 20 56 45 4e 44 4f 52 3a 20 41 4d 42 49 54 3b 20 42 4f 4f 54 52 3a 20 33 2e 31 2e 36 64 3b 20 53 57 5f 52 45 56 3a 20 32 2e 39 34 2e 31 30 3 1 35 3b 20 4d 4f 44 45 4c 3a 20 45 30 38 43 30 30 37 3e 3e 0 0 0 0 0
Tag : 6a, Length : 8, Value =33 2e 31 2e 36 64 0 0
Tag : 6b, Length : 8, Value =31 2e 31 39 0 0 0 0
Tag : 65, Length : 16, Value =32 2e 39 34 2e 31 30 31 35 0 0 0 0 0 0 0
Tag : 66, Length : 16, Value =32 2e 39 34 2e 31 30 31 35 0 0 0 0 0 0 0
Tag : 67, Length : 24, Value =31 2e 33 2e 36 2e 31 2e 34 2e 31 2e 34 36 38 34 2e 32 2e 31 2e 36 0 0
Tag : 68, Length : 44, Value =41 6d 62 69 74 20 63 61 62 6c 65 6d 6f 64 65 6d 20 61 67 65 6e 74 20 76 65 72 73 69 6f 6e 20 32 0 0 0 0 0 0 0 0 0 0 0 0
Tag : 69, Length : 28, Value =31 2e 33 2e 36 2e 31 2e 34 2e 31 2e 34 36 38 34 2e 32 2e 33 2e 31 2e 31 2e 32 2e 31
vvv Interface creation and driver startup beginning vvv
-> Begin DOCSIS CM WAN interface
Creating HAL object for the DOCSIS CableModem interface
numFreqPlan 4
Registering DOCSIS CableModem driver
0000000 - The DS Channel List is being updated (RFI-N-03.0086).
0000001 - The list is empty; adding a single default scanning entry.
-> End DOCSIS CM WAN interface
-> Begin Ethernet LAN interfaces
Creating HAL object for the Ethernet interface
Registering Ethernet driver
-> End Ethernet LAN interfaces
-> Begin USB LAN interface
Creating HAL object for the USB 1.1 interface
Registering USB driver
0000002 - CM HAL reports h/w support for PHS, bitmask=3
0000003 - CM HAL reports h/w support for PHS, size=64
-> End USB LAN interface
-> Begin IP Stack interfaces
-> Starting V2 DHCP Client subsystem...
Creating HAL object for IP Stack1 (MAC Addr=00:14:a4:c2:86:9f)
Registering IP Stack1 driver
Creating HAL object for IP Stack2 (MAC Addr=00:02:8a:de:ad:02)
Registering IP Stack2 driver
IP Stack3 not enabled or failed to create and start interface; no other stacks will be loaded.
-> End IP Stack interfaces
^^^ Interface creation and driver startup complete ^^^
Propane version: 2.0.1 (28 Oct 2002)
DON'T think we need to go here - so don't:::: init_mib !!!!
WARNING: netsnmp_brcm_create_tstring called with no address!
Creating SNMP agent cablemodem agent
Creating SNMP agent CPE diag agent
0000004 - Successfully added MAC Management address to CAM
0000005 - Interface 10 additional registration w/ SNMP agent OK.
************************************
*** Start up CPU load monitor module
************************************
*
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* * * *
* * * * * * ***
* * * * * * * * *******************
* * * * * *
* *
Broadcom Corporation Reference Design
+----------------------------------------------------------------------------+
| _/_/ _/_/_/_/ _/_/ |
| _/ _/ _/ _/ _/ Broadband |
| _/ _/ _/ _/ |
| _/_/ _/_/_/ _/ Foundation |
| _/ _/ _/ _/ |
| _/ _/ _/ _/ _/ Classes |
| _/_/_/ _/ _/_/ |
| |
| Copyright (c) 1999 - 2005 Broadcom Corporation |
| |
| Revision: 3.9.32 RELEASE |
| |
| Features: MinimalConsole Nonvol Slim HeapManager SNMP Networking USB1.1 |
+----------------------------------------------------------------------------+
| Standard Embedded Target Support for BFC |
| |
| Copyright (c) 2003-2004 Broadcom Corporation |
| |
| Revision: 3.0.1 RELEASE |
| |
| Features: PID=0xa603 Bootloader-Rev=3.1.6d |
| Features: Bootloader-Compression-Support=0x19 |
+----------------------------------------------------------------------------+
| eCos BFC Application Layer |
| |
| Copyright (c) 1999 - 2004 Broadcom Corporation |
| |
| Revision: 3.0.2 RELEASE |
| |
| Features: eCos Console Cmds, (no Idle Loop Profiler) |
+----------------------------------------------------------------------------+
| _/_/ _/ _/ |
| _/ _/ _/_/ _/_/ DOCSIS Cable Modem |
| _/ _/ _/ _/ |
| _/ _/ _/ |
| _/ _/ _/ |
| _/ _/ _/ _/ |
| _/_/ _/ _/ |
| |
| Copyright (c) 1999 - 2005 Broadcom Corporation |
| |
| Revision: 3.9.32 RELEASE |
| |
| Features: AckCel(tm) DOCSIS 1.0/1.1/2.0 Propane(tm) CM SNMP w/Factory MIB |
| Features: Support CM Vendor Extension |
+----------------------------------------------------------------------------+
| Broadcom Data-Only CM Vendor Extension |
| |
| Copyright (c) 1999 - 2004 Broadcom Corporation |
| |
| Revision: 3.6.2 RELEASE |
| |
| Features: DHCP Server HTTP Server OSS2-N-03025 Visualization LED |
| Features: Controller |
+----------------------------------------------------------------------------+
| Build Date: Mar 6 2009 |
| Build Time: 16:54:37 |
| Built By: betty |
| Firmware version : 2.94.1015 |
| Hidden version : 2.94.1015 |
+----------------------------------------------------------------------------+
Disable console output
[/code]