hehe, wait until you see the secure boot on some modems, I posted a fw for a modem that supports secure boot via atom/uefi, that will be REAL fun. thankfully they left the modems open to the net and you can even make the SNMP queries on their stupid fucking web 5.0 fucking bullshit interface.
have you decompiled the firmware image and looked at the uboot startup script? lots of fuckery goes on in there (disabling serial output, firmware checking etc), as some run this firmware called OpenRG, where your modem actually downloads the firmware and runs it to ram.
Could you shoot me a PM with the firmware images you have of Puma5 RG/Modems, esp the newer 480s', I believe they are the same as a netgear/smc 8x4 hardware wise? I'll take a look and see whats going on when i have time.
hehe, wait until you see the secure boot on some modems, I posted a fw for a modem that supports secure boot via atom/uefi, that will be REAL fun. thankfully they left the modems open to the net and you can even make the SNMP queries on their stupid fucking web 5.0 fucking bullshit interface.
EX: "Start download image from Scorpion...*** Running from RAM partition @0x87000000"
EX: "checking section 3... ok: 'Image downloaded from: https://213.60.177.100:550/firmwares/ope..._32.rms?ua"
but no one will post images of the firmwares, its not possible without seeing puma5 firmware images whats going on really.. and a good debugger.
as for the settings reverting, its because many reasons. nvram offsets and shit that goes on when you mix and match firmwares, sometimes you gotta zero the ENTIRE Flash chip, and reload your bin. example: i've put a 6141 firmware on a ubee modem, and when i booted into the ubee firmware, changed macs, and such it was fine, then booted into the 6141 firmware and it had stock macs and all, so i cleared that, then it fucked up the ubee image and the ubee image detected this and set it to boot back into the 6141 image and all sorts of fuckery.
Could you shoot me a PM with the firmware images you have of Puma5 RG/Modems, esp the newer 480s', I believe they are the same as a netgear/smc 8x4 hardware wise? I'll take a look and see whats going on.
for example: take this uboot sourcecode:
https://github.com/duyunfu/U-boot/blob/m....2.0/notes
they silenced the output, but were too dumb too silence the input... so you can either dump the nvram and hexedit silent out, some also skip the uboot boot to cmd line sequence all together, then you gotta modify the uboot or figure out how to glitch it into a shell.. there are also variables for skipping the option to drop to console but still outputting uboot serial console.
ps; i am bad at forums, somehow my post got edited and doubled its self and did all sorts of wacky shit.
have you decompiled the firmware image and looked at the uboot startup script? lots of fuckery goes on in there (disabling serial output, firmware checking etc), as some run this firmware called OpenRG, where your modem actually downloads the firmware and runs it to ram.
Could you shoot me a PM with the firmware images you have of Puma5 RG/Modems, esp the newer 480s', I believe they are the same as a netgear/smc 8x4 hardware wise? I'll take a look and see whats going on when i have time.
hehe, wait until you see the secure boot on some modems, I posted a fw for a modem that supports secure boot via atom/uefi, that will be REAL fun. thankfully they left the modems open to the net and you can even make the SNMP queries on their stupid fucking web 5.0 fucking bullshit interface.
EX: "Start download image from Scorpion...*** Running from RAM partition @0x87000000"
EX: "checking section 3... ok: 'Image downloaded from: https://213.60.177.100:550/firmwares/ope..._32.rms?ua"
but no one will post images of the firmwares, its not possible without seeing puma5 firmware images whats going on really.. and a good debugger.
as for the settings reverting, its because many reasons. nvram offsets and shit that goes on when you mix and match firmwares, sometimes you gotta zero the ENTIRE Flash chip, and reload your bin. example: i've put a 6141 firmware on a ubee modem, and when i booted into the ubee firmware, changed macs, and such it was fine, then booted into the 6141 firmware and it had stock macs and all, so i cleared that, then it fucked up the ubee image and the ubee image detected this and set it to boot back into the 6141 image and all sorts of fuckery.
Could you shoot me a PM with the firmware images you have of Puma5 RG/Modems, esp the newer 480s', I believe they are the same as a netgear/smc 8x4 hardware wise? I'll take a look and see whats going on.
for example: take this uboot sourcecode:
https://github.com/duyunfu/U-boot/blob/m....2.0/notes
Code:
LINUX boot related stuff
-------------------------
- When CONFIG_SILENT_CONSOLE is defined, all console messages (by
U-Boot and Linux!) can be silenced with the "silent" environment
variable. See doc/README.silent for more information.ps; i am bad at forums, somehow my post got edited and doubled its self and did all sorts of wacky shit.