12-11-2012, 02:05 AM
(This post was last modified: 12-11-2012, 02:28 AM by mandrake77.)
Code:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.11.11 19:54:56 =~=~=~=~=~=~=~=~=~=~=~=
Haxorware integrated telnet daemon
Username: root
Password: *****
Welcome.
CM>
CM> run
CM>
CM> run_app
Running the system...
Beginning Cable Modem operation...
0x0000c62a [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Scanning for a Downstream Channel...
mot_scanList: Setting override freq @ 0
Favorite[0].freq = 699000000
Attempting Downstream FEC lock @ freq= 699000000 Hz, QAM64/256
CM> Found energy at frequency 699000000Hz! Publishing event kEventEnergyDetected...
0x0000c88c [CmDocsisCtlThread] BcmCmDocsisCtlThread::StartUsInit: (CmDocsisCtlThread) Locked on the downstream. Waiting for UCDs...
******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 699000000 Hz
Carrier Offset = 3 Hz
Symbol rate = 5360537 sym/sec
SNR = 40 dB
QAM Mode = QAM256
Tuner AGC = 0xfff00000
IF AGC = 0x1402abc6
Power Level = 6 dB
QAM = LOCKED
FEC = LOCKED
******************************************
CM> Selecting UCD for Us Channel 10
0x0000d232 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchDsTimeSync: (CmDocsisCtlThread) starting ds time sync acquisition...
0x0000d4d0 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) downstream time sync acquired...
0x0000d4d0 [CmDocsisCtlThread] BcmCmDocsisCtlThread::DsSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 45.0 dBmV
0x0000d4d0 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) rx unexpected kDsSyncOk indication...
Not logging event ID 2307948724, control for level 7 is 0.
CM>
RNG-RSP Adj: tim=1461 power=-1 freq=0 Stat=Continue
CM>
RNG-RSP Adj: tim=0 power=-1 freq=-290 Stat=Success
******************************************
UPSTREAM STATUS
******************************************
Upstream Status = UP
Upstream Channel = 10
Upstream Frequency = 25000000 Hz
Upstream Power = 44 dBmV
Ranging SID = 0x1438
Upstream Symbol Rate = 2560000 sym/sec
******************************************
Calculating maximum number of IP filters:
Each IP filter consumes 1864 bytes of RAM.
Current free RAM is 424704 bytes.
Max heap reserved for IP filters (25%) = 106176
We can support 56 IP filters.
Calculating maximum number of LLC filters:
Each LLC filter consumes 744 bytes of RAM.
Current free RAM is 424684 bytes.
Max heap reserved for LLC filters (25%) = 106171
We can support 142 LLC filters.
Starting IP Initialization with DHCP...
DHCPc: Waiting 4 seconds before sending Discover; client id htype=1, value=00:1a:XX:XX:XX:XX
Not logging event ID 2307948624, control for level 7 is 0.
CM> 0x0000e164 [DHCP Server Thread] BcmDhcpServerThread::ThreadMain: (DHCP Server Thread) Callback request expired:
timerDuration secs = 1
current time secs = 57
elapsed time secs = 1
CM> DHCPc: Sending Discover packet; client id htype=1, value=00:1a:XX:XX:XX:XX
DHCPc: Received an Offer from DHCP server 00:01:XX:XX:XX:XX (10.7.224.1); lease client id htype=1, value=00:1a:XX:XX:XX:XX
CM> DHCPc: Timed out waiting for offers for lease with client id htype=1, value=00:1a:XX:XX:XX:XX
DHCPc: Sending Request packet; client id htype=1, value=00:1a:XX:XX:XX:XX
DHCPc: Received an Ack from DHCP server 00:01:XX:XX:XX:XX (10.7.224.1); lease client id htype=1, value=00:1a:XX:XX:XX:XX
Current IP address is default 0.0.0.0.
0x0000f50a [DHCP Client Thread] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack1 HalIf)
Configuring IP stack 1:
IP Address = 10.7.224.237 (primary IP address)
Subnet Mask = 255.255.252.0
Router = 10.7.224.1
IsPrimaryInterface = 1
Logging event: DHCP WARNING - Non-critical field invalid in response.
ARPing for default GW IP = 10.7.224.1
MAC = 00:01:XX:XX:XX:XX
DHCP completed successfully!
DHCP Settings:
Client Id = htype=1, value=00:1a:XX:XX:XX:XX
State = Renewing (5)
Static Lease = 0
AutoConfig Mode = IP, Subnet and Router
XID = 0x1054fdbd
Number of Tries = 0
Max Discover Tries = 6
Max Request Tries = 6
DHCP server MAC addr = 00:01:XX:XX:XX:XX
Ignore NAKs = 0
My offered IP address = 10.7.224.237 (primary IP address)
(1) Subnet Mask = 255.255.252.0
(3) Router IP address = 10.7.224.1
(54) DHCP Server IP address = 192.168.10.10
(82) Relay Agent IP address = 10.7.224.1
TFTP Server IP address = 10.7.224.1
CM Configuration file = 'cm-001XXXXXXX'
(2) UTC Time Offset = -18000 seconds
(4) Time Server IP address = 192.168.10.24
(6) Domain Name Server =
(7) Log Server IP address = 200.75.200.7
(51) Lease time = 2929 seconds
(58) T1 (renew) = 1464 seconds
(59) T2 (rebind) = 2562 seconds
Lease is infinite = 0
(122) PacketCable/CableHome -== SubOptions ==-
SubOpt(1) Primary Dhcp Server = 255.255.255.255
SB5102 CM Agent w/ BRCM Factory Support IpStackEvent: Ip=10.7.224.237, Subnet=255.255.252.0, Gateway=10.7.224.1
CmSnmpAgent::IpAddressAcquiredEvent for SB5102 CM Agent w/ BRCM Factory Support
IP addr = 10.7.224.237
Starting Time Of Day...
0x0000f5aa [CmDocsisIpThread] BcmDocsisTimeOfDayThread::SetTodServerIpAddress: (Time Of Day Thread) ToD servers: 192.168.10.24
Connecting to ToD server 192.168.10.24...
Sending UDP ToD request to server...
SNMP Agent Binding to 10.7.224.237:225
Not logging event ID 2291949724, control for level 7 is 0.
CM> UTC returned by ToD server 3561670522; UTC offset -18000
Current system time -> Sun Nov 11 19:55:22 2012
System start time -> Sun Nov 11 19:54:19 2012
Starting Tftp of configuration file...
Opening file 'cm-001XXXXXXX' on 10.7.224.1 for reading...
tftp-enforce bypass is using 10.7.224.1:cm-001XXXXXXX
Initiating fake TFTP Get (tftp-enforce bypass)
Bypass succeeded.File was 900 bytes
Storing received cfg of size 900 to memory
Tftp read < 512 bytes, we have reached end of file.
Tftp transfer complete!
TFTP Settings:
Stack Interface = 1
Server Ip Address = 10.7.224.1
Server Port Number = 6934
Total Blocks Read = 2
Total Bytes Read = 900
Config file was read! IP Initialization completed...
MAX CPE per CM is being set to 32
TLV-11[1]: 1.3.6.1.2.1.69.1.2.1.7.1 -> 4 (i32)
TLV-11[2]: 1.3.6.1.2.1.69.1.2.1.2.1 -> 192.168.129.128
TLV-11[3]: 1.3.6.1.2.1.69.1.2.1.3.1 -> 255.255.255.128
TLV-11[4]: 1.3.6.1.2.1.69.1.2.1.4.1 -> private
TLV-11[5]: 1.3.6.1.2.1.69.1.2.1.5.1 -> 3 (i32)
TLV-11[6]: 1.3.6.1.2.1.69.1.2.1.6.1 -> @
TLV-11[7]: 1.3.6.1.2.1.69.1.2.1.7.2 -> 4 (i32)
TLV-11[8]: 1.3.6.1.2.1.69.1.2.1.2.2 -> 192.168.10.0
TLV-11[9]: 1.3.6.1.2.1.69.1.2.1.3.2 -> 255.255.255.0
TLV-11[10]: 1.3.6.1.2.1.69.1.2.1.4.2 -> private
TLV-11[11]: 1.3.6.1.2.1.69.1.2.1.5.2 -> 3 (i32)
TLV-11[12]: 1.3.6.1.2.1.69.1.2.1.6.2 -> @
TLV-11[13]: 1.3.6.1.2.1.69.1.2.1.7.3 -> 4 (i32)
TLV-11[14]: 1.3.6.1.2.1.69.1.2.1.2.3 -> 192.168.129.128
TLV-11[15]: 1.3.6.1.2.1.69.1.2.1.3.3 -> 255.255.255.128
TLV-11[16]: 1.3.6.1.2.1.69.1.2.1.4.3 -> private
TLV-11[17]: 1.3.6.1.2.1.69.1.2.1.5.3 -> 3 (i32)
TLV-11[18]: 1.3.6.1.2.1.69.1.2.1.6.3 -> HEX:C7
TLV-11[19]: 1.3.6.1.2.1.69.1.2.1.7.4 -> 4 (i32)
TLV-11[20]: 1.3.6.1.2.1.69.1.2.1.2.4 -> 200.75.200.26
TLV-11[21]: 1.3.6.1.2.1.69.1.2.1.3.4 -> 255.255.255.255
TLV-11[22]: 1.3.6.1.2.1.69.1.2.1.4.4 -> private
TLV-11[23]: 1.3.6.1.2.1.69.1.2.1.5.4 -> 3 (i32)
TLV-11[24]: 1.3.6.1.2.1.69.1.2.1.6.4 -> @
TLV-11[25]: 1.3.6.1.2.1.69.1.6.3.0 -> 2 (i32)
TLV-11[26]: 1.3.6.1.2.1.69.1.2.1.8.1 -> 1 (i32)
TLV-11[27]: 1.3.6.1.2.1.69.1.6.1.0 -> 2 (i32)
TLV-11[28]: 1.3.6.1.4.1.4115.10.1.20.0 -> 1049648 (i32) UNKNOWN, ignoring.
TLV-11[29]: 1.3.6.1.4.1.4115.1.3.1.1.2.3.2.0 -> 2 (i32) UNKNOWN, ignoring.
TLV-11[30]: 1.3.6.1.4.1.4115.1.3.1.1.2.3.5.4.0 -> 3 (i32) UNKNOWN, ignoring.
TLV-11[31]: 1.3.6.1.4.1.4115.1.3.1.1.2.3.5.3.0 -> 3 (i32) UNKNOWN, ignoring.
Time Of Day completed...
DefaultSnmpAgentClass::SystemTimeChangeEvent for SB5102 CM Agent w/ BRCM Factory Support
Not logging event ID 2291949524, control for level 7 is 0.
Not logging event ID 2291949324, control for level 7 is 0.
SB5102 CM Agent w/ BRCM Factory Support processing TLV-11's
SNMP packet sent to 10.7.224.237:225
31 TLV-11's OK.
Sending a REG-REQ to the CMTS...
Logging event: TLV-11 - unrecognized OID
Received a REG-RSP message from the CMTS...
0x0000f97e [CmDocsisCtlThread] BcmCmDocsisCtlThread::RegRspMsgEvent: (CmDocsisCtlThread) We registered with a DOCSIS 1.1 config file!
0x0000f97e [CmDocsisCtlThread] BcmCmDocsisCtlThread::TxRegAckMsg: (CmDocsisCtlThread) upstream already using standard short/long grant profiles. downshift NOT required.
Logging event: TLV-11 - unrecognized OID
Logging event: TLV-11 - unrecognized OID
Logging event: TLV-11 - unrecognized OID
0x0000f988 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TxRegAckMsg: (CmDocsisCtlThread) upstream type 2 upshift to adv phy burst profiles!
Registration complete!
Process CVC
0x0000f992 [CmDocsisCtlThread] CmSecureDownload::ProcessConfigFileManufAndCosignerCvcs: (Secure Software Download) WARNING - No CVC included in config file; software upgrade can't be performed!
0x0000f992 [CmDocsisCtlThread] BcmCmDocsisCtlThread::ProcessCVC: (CmDocsisCtlThread) ERROR - Config file does not include a valid CVC!
DOCSIS CoS/QoS rate shaping enable is now 1
CmSnmpAgent::CmOperationalEvent for SB5102 CM Agent w/ BRCM Factory Support
CmSnmpAgent operating in 1.1 mode, including docsQos, excluding docsBpi
+++ No DH kickstart profiles or snmpCommunityTable entries installed.
We will operate in NMACCESS mode.
SB5102 CM Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
SB5102 CM Agent w/ BRCM Factory Support enabling management.
SB5102 CM Agent w/ BRCM Factory Support sending deferred traps...
Done w/ deferred traps.
SB5102 CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
0x0000f99c [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchBpkm: (CmDocsisCtlThread) BPKM enabled. starting BPKM key requests.
SB5102 CM Event Log w/ BRCM Factory Support sending deferred async messages...
Sending syslog message from IF 1 to 200.75.200.7:
<133> CABLEMODEM [DOCSIS]: <73040100> TLV-11 - unrecognized OID
Sending syslog message from IF 1 to 200.75.200.7:
<133> CABLEMODEM [DOCSIS]: <73040100> TLV-11 - unrecognized OID
Sending syslog message from IF 1 to 200.75.200.7:
<133> CABLEMODEM [DOCSIS]: <73040100> TLV-11 - unrecognized OID
Sending syslog message from IF 1 to 200.75.200.7:
<133> CABLEMODEM [DOCSIS]: <73040100> TLV-11 - unrecognized OID
Done w/ deferred msgs
Not logging event ID 66040100, control for level 7 is 0.
BPI initialization completed. Calling ConfigOperational().
Enabling network access for all CPE ports.
mot_scanList: Writing to Flash!
BcmCmDocsisStatusEventCodes::kCmIsOperational
Suspending SNMP Thread
0x0000fbcc [CmDocsisCtlThread] BcmVendorCmApplication::StopDhcpServer: (VendorExtension CmApp) Shutting down DHCP Server...
0x0000fbcc [CmDocsisCtlThread] BcmStandbySwitchThread::CmIsOperational: (Motorola Standby Switch Thread) Simulating a press of the standby switch to get the state configured properly.
0x0000fbd6 [IGMP Thread] BcmIgmpThread::Starting Igmp Thread...: (IGMP Thread)
0x0000fbd6 [Motorola Standby Switch Thread] BcmStandbySwitchThread::ThreadMain: (Motorola Standby Switch Thread) Standby switch was pressed!
0x0000fbd6 [Motorola Standby Switch Thread] BcmStandbySwitchThread::ProcessSwitchEvent: (Motorola Standby Switch Thread) Standby switch disabled in nonvol; ignoring event.
Not logging event ID 2296948624, control for level 7 is 0.
********************
At this point I get wallgardened... I can "provision" myself an IP, but will get me throttled (and only google)...
"Autoserving" me the same config the CMTS is providing me will result in an endless bootloop (but with 49TLVs instead of 31)...
Im assuming the CM is rebooting due to the CMIC md5 hash (at the end of the cfg) not been the one the CMTS wants... will Taco's old "0.0.0.0" suggestion to the cfg will aid this?
Thanks m8s[hr]http://pastebin.com/X7BTK7Ae