Thread Rating:
  • 1 Vote(s) - 1 Average
  • 1
  • 2
  • 3
  • 4
  • 5
TFTP failed - configuration file NOT FOUND
#1
I'm playing to increase the speed of my modem (Haxorware 5101) by using differents MACs and Certs. When I try to use a MAC and Certs with speed 10/1, every things is fine but when I use a MAC and Certs with speed higher 20/2, modem cannot online with log like this:

0x000127d2 [CmDocsisIpThread] BcmCmDocsisIpThread::RestartTftpConfigFile: (CmDocsisIpThread) ERROR - Failed to TFTP config file after 4 tries! Aborting...
0x000127dc [CmDocsisCtlThread] BcmCmDocsisCtlThread::IpInitErrorEvent: (CmDocsisCtlThread) ERROR - IP helper returned kTftpInitFailed error! Restarting!
0x000127dc [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncRestartErrorEvent: (CmDocsisCtlThread) reason: 12 (kTftpInitFailed)
Logging event: TFTP failed - configuration file NOT FOUND

All these MACs and Certs are valide.
Reply
#2
what does the log say around the time of the initial tftp get
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#3
I don't have a MAX232 to setup a Putty Log. I just telnet to my modem and focus this error. Another logs around that time look OK.
Reply
#4
Some more log:

Logging event: TFTP failed - configuration file NOT FOUND
CM> 0x000b4708 [DHCP Server Thread] BcmDhcpServerThread::ThreadMain: (DHCP Server Thread) Callback request expired:
timerDuration secs = 1
current time secs = 739
elapsed time secs = 1
CM> 0x000b7232 [DHCP Server Thread] BcmDhcpServerThread::ThreadMain: (DHCP Server Thread) Callback request expired:
timerDuration secs = 1
current time secs = 750
elapsed time secs = 1
CM> Starting Tftp of configuration file...
Opening file 'dynamic config xxxxxxxxxxxxxxxxxxxxxx' on xx.xx.xx.xx for reading...
tftp-enforce bypass is using xx.xx.xx.xx:dynamic config xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Initiating fake TFTP Get (tftp-enforce bypass)
Bypass failed.Error Illegal operation
0x000b82fe [CmDocsisIpThread] Tftp Client::Send: (Tftp Client) ERROR - Recv'd error code (1) - <File not found>
0x000b8308 [CmDocsisIpThread] BcmCmDocsisIpThread::TftpConfigFile: (CmDocsisIpThread) ERROR - Failed to open the file on the TFTP server!
0x000b8308 [CmDocsisIpThread] BcmCmDocsisIpThread::RestartTftpConfigFile: (CmDocsisIpThread) ERROR - Failed to TFTP config file after 4 tries! Aborting...0x000b8308 [CmDocsisCtlThread] BcmCmDocsisCtlThread::IpInitErrorEvent: (CmDocsi
sCtlThread) ERROR - IP helper returned kTftpInitFailed error! Restarting!
0x000b8308 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncRestartErrorEvent: (CmDocsisCtlThread) reason: 12 (kTftpInitFailed)
Logging event: TFTP failed - configuration file NOT FOUND
Not logging event ID 2436694038, control for level 7 is 0.
Logging event: Tftp Init Failed - Reinitialize MAC...
Deleting DOCSIS 1.0 CoS Settings for SID 0x1d520x000b83d0 [CmDocsisCtlThread] BcmDocsisCmHalIf:Big GrineleteAllServiceFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service Flows, along with associated Classifiers and PHS rules...Stopping DHCP/ToD/TFTP (client requested)...
The ToD thread was stopped.
DHCPc: Releasing the lease with client id htype=1, value=xx:xx:xx:xx:xx:xx
DHCPc: Sending Release packet; client id htype=1, value=xx:xx:xx:xx:xx:xx
0x000b83da [DHCP Client Thread] BcmDhcpClientIf::SendDhcpPacket: (DHCP ClientIf for IP Stack1) WARNING - Failed to send packet!
0x000b83da [DHCP Client Thread] BcmDhcpClientIf::SendRelease: (DHCP ClientIf for IP Stack1) WARNING - Failed to create/send Release packet! Oh, well, no biggie...
0x000b83e4 [DHCP Client Thread] BcmEcosIpHalIf::RemoveLeaseImpl: (IP Stack1 HalIf) Removing lease IP address xx.xx.xx.xx from IP stack 1
0x000b83e4 [DHCP Client Thread] BcmEcosIpHalIf::RemoveLeaseImpl: (IP Stack1 HalIf) This is the last address on the stack; shutting the stack down:numberOfAddresses=1
0x000b83e4 [DHCP Client Thread] BcmEcosIpHalIf::ShutdownIpStackImpl: (IP Stack1 HalIf)
Shutting down IP stack 1
SB5102 CM Agent w/ BRCM Factory Support IpStackEvent: Ip=0.0.0.0, Subnet=0.0.0.0, Gateway=0.0.0.0
CM> DefaultSnmpAgentClass::RestartPendingEvent for SB5102 CM Agent w/ BRCM Factory Support
SB5102 CM Agent w/ BRCM Factory Support resetting to default state.
SB5102 CM Agent w/ BRCM Factory Support destroying users...
Pausing trap thread
SB5102 CM Agent w/ BRCM Factory Support destroying notifies...
Resuming trap thread
SB5102 CM Agent w/ BRCM Factory Support destroying views...
SB5102 CM Agent w/ BRCM Factory Support sending deferred traps...
Done w/ deferred traps.
SB5102 CM Event Log w/ BRCM Factory Support sending deferred async messages...
Done w/ deferred msgs
SB5102 CM Agent w/ BRCM Factory Support defering traps.
SB5102 CM Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted
SB5102 CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisCpeView
Non-Vol Settings successfully written to the device.
0x000b84de [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 170x000b84de [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain:
(Scan Downstream Thread) Downstream Channel scan stopped!
0x000b84f2 [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain:
(Scan Downstream Thread) Scanning for a Downstream Channel...

mot_scanList: Setting override freq @ 0
Favorite[2].freq = 693000000
Attempting Downstream FEC lock @ freq= 693000000 Hz, QAM64/256
CM> Found energy at frequency 693000000Hz! Publishing event kEventEnergyDetected...
0x000b8740 [CmDocsisCtlThread] BcmCmDocsisCtlThread::StartUsInit: (CmDocsisCtlThread) Locked on the downstream. Waiting for UCDs...
mot_scanList: Setting override freq @ 705000000
Scanning DS Channel at 705000000 Hz... (Initial target freq)
CM> Found energy at frequency 705000000Hz! Publishing event kEventEnergyDetected...
0x00013c4a [CmDocsisCtlThread] BcmCmDocsisCtlThread::StartUsInit: (CmDocsisCtlThread) Locked on the downstream. Waiting for UCDs...

******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 705000000 Hz
Carrier Offset = 12 Hz
Symbol rate = 5360537 sym/sec
SNR = 35 dB
QAM Mode = QAM256
Tuner AGC = 0xfff00000
IF AGC = 0x17a6e937
Power Level = -10 dB
QAM = LOCKED
FEC = LOCKED
******************************************

CM> Selecting UCD for Us Channel 9

0x00014726 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchDsTimeSync: (CmDocsisCtlThread) starting ds time sync acquisition...
0x000149ba [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) downstream time sync acquired...
0x000149ba [CmDocsisCtlThread] BcmCmDocsisCtlThread:Big GrinsSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 55.0 dBmV
0x000149c4 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) rx unexpected kDsSyncOk indication...
Not logging event ID 2307948724, control for level 7 is 0.
RNG-RSP Adj: tim=2010 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=1 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Success

******************************************
UPSTREAM STATUS
******************************************
Upstream Status = UP
Upstream Channel = 9
Upstream Frequency = 30700000 Hz
Upstream Power = 56 dBmV
Ranging SID = 0x19ef
Upstream Symbol Rate = 5120000 sym/sec
******************************************

Starting IP Initialization with DHCP...
DHCPc: Waiting 1 seconds before sending Discover; client id htype=1, value=xx:xx:xx:xx:xx:xx
Not logging event ID 2307948624, control for level 7 is 0.
CM> DHCPc: Sending Discover packet; client id htype=1, value=xx:xx:xx:xx:xx:xx
DHCPc: Received an Offer from DHCP server xx:xx:xx:xx:xx:xx (xx:xx:xx:xx:xx:xx); leas
e client id htype=1, value=xx:xx:xx:xx:xx:xx
0x00015c20 [DHCP Server Thread] BcmDhcpServerThread::ThreadMain: (DHCP Server Thread) Callback request expired:
timerDuration secs = 1
current time secs = 89
elapsed time secs = 1
CM> DHCPc: Timed out waiting for offers for lease with client id htype=1, value=xx:xx:xx:xx:xx:xx
DHCPc: Sending Request packet; client id htype=1, value=xx:xx:xx:xx:xx:xx
DHCPc: Received an Ack from DHCP server xx:xx:xx:xx:xx:xx (xx:xx:xx:xx:xx:xx); lease
client id htype=1, value=xx:xx:xx:xx:xx:xx
Current IP address is default 0.0.0.0.
0x0001640e [DHCP Client Thread] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack1HalIf)
Configuring IP stack 1:
IP Address = xx.xx.xx.xx (primary IP address)
Subnet Mask = 255.255.252.0
Router = xx.xx.xx.xx
IsPrimaryInterface = 1

Logging event: DHCP WARNING - Non-critical field invalid in response.
ARPing for default GW IP = xx.xx.xx.xx
MAC = xx:xx:xx:xx:xx:xx
DHCP completed successfully!

DHCP Settings:
Client Id = htype=1, value=xx:xx:xx:xx:xx:xx
State = Renewing (5)
Static Lease = 0
AutoConfig Mode = IP, Subnet and Router
XID = 0x7c79c1a1
Number of Tries = 0
Max Discover Tries = 6
Max Request Tries = 6
DHCP server MAC addr = xx:xx:xx:xx:xx:xx
Ignore NAKs = 0
My offered IP address = xx.xx.xx.xx (primary IP address)
(1) Subnet Mask = 255.255.252.0
(3) Router IP address = xx.xx.xx.xx
(54) DHCP Server IP address = xx.xx.xx.xx
(82) Relay Agent IP address = xx.xx.xx.xx
TFTP Server IP address = xx.xx.xx.xx
CM Configuration file = dynamic config xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
(2) UTC Time Offset = 0 seconds
(4) Time Server IP address = xx.xx.xx.xx
(6) Domain Name Server = xx.xx.xx.xx; xx.xx.xx.xx
(7) Log Server IP address =
(51) Lease time = 429399 seconds
(58) T1 (renew) = 214699 seconds
(59) T2 (rebind) = 375724 seconds
Lease is infinite = 0


SB5102 CM Agent w/ BRCM Factory Support IpStackEvent: Ip=xx.xx.xx.xx, Subnet=255.255.252.0, Gateway=xx.xx.xx.xx
CmSnmpAgent::IpAddressAcquiredEvent for SB5102 CM Agent w/ BRCM Factory Support
IP addr = xx.xx.xx.xx
Starting Time Of Day...
0x000164a4 [CmDocsisIpThread] BcmDocsisTimeOfDayThread::SetTodServerIpAddress:
(Time Of Day Thread) ToD servers: xx.xx.xx.xx
Connecting to ToD server xx.xx.xx.xx...
Sending UDP ToD request to server...
SNMP Agent Binding to xx.xx.xx.xx:225
Not logging event ID 2291949724, control for level 7 is 0.
UTC returned by ToD server 3537750910; UTC offset 0
Current system time -> Thu Feb 09 04:35:10 2012

System start time -> Thu Feb 09 04:33:39 2012

Starting Tftp of configuration file...
Opening file 'dynamic config xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx' on xx.xx.xx.xx for reading...
tftp-enforce bypass is using dynamic config xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Initiating fake TFTP Get (tftp-enforce bypass)
Bypass failed.Error Illegal operation
0x00016652 [CmDocsisIpThread] Tftp Client::Send: (Tftp Client) ERROR - Recv'd error code (1) - <File not found>
0x0001665c [CmDocsisIpThread] BcmCmDocsisIpThread::TftpConfigFile: (CmDocsisIpThread) ERROR - Failed to open the file on the TFTP server!
0x0001665c [CmDocsisIpThread] BcmCmDocsisIpThread::RestartTftpConfigFile: (CmDocsisIpThread) ERROR - Failed to read the config file, or it was rejected by the client!
0x0001665c [CmDocsisIpThread] BcmCmDocsisIpThread::RestartTftpConfigFile: (CmDocsisIpThread) ERROR - Will try again later...(after 20 seconds).
0x0001665c [CmDocsisIpThread] BcmCmDocsisIpThread::RestartTftpConfigFile: (CmDocsisIpThread) WARNING -
**
*
* Using non-DOCSIS compliant TFTP retry timeout value from nonvol!
* DOCSIS requires 600 seconds!
*
**

Time Of Day completed...
DefaultSnmpAgentClass::SystemTimeChangeEvent for SB5102 CM Agent w/ BRCM Factory Support
Logging event: TFTP failed - configuration file NOT FOUND
Not logging event ID 2291949324, control for level 7 is 0.
CM>
Reply
#5
turn off bypass/forcing

Initiating fake TFTP Get (tftp-enforce bypass)
Bypass failed.Error Illegal operation
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#6
I did but it did not work.
Reply
#7
same error in telnet or different?
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#8
When I uncheck TFTP bypass, there was no more these errors:

Initiating fake TFTP Get (tftp-enforce bypass)
Bypass failed.Error Illegal operation

But there still was: TFTP failed - configuration file NOT FOUND
Reply
#9
i've seen this before the force config page shows nothing is being forced but in telnet it still shows that it is
in telnet (coax unplugged)
Code:
cd /d
scan_stop
cd /n/d
enable force_cfgfile false

cant remember if next bit was needed or not

dhcp_settings
My IP Address: {hit enter}
Subnet Mask: {hit enter}
Router IP Address: {hit enter}
Those are the only 3 that really need to be changed
Do you want to change the other settings? [no] (hit Y}
TFTP Server IP Address: {hit enter}
Config file name: {hit enter}
Time Server IP Address: {hit enter}
SysLog Server IP Address: {hit enter}

saying that reset to defaults should do the same thing
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#10
I just do every things as you said but it is still show: TFTP failed - configuration file NOT FOUND

I know that Force Config doesn't work anymore but how I can Force ONLY TFTP?
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)