newbie, in log critical and error

[zarkocg68]

Hello,

I have a EPC2100R2 and after the flashing i have stay in configuration about frequency, and MAC and other ....

I get in status that my modem are connected and i get ip adress for internet. But when i try to open a web page i see that he dont is connected. here logs :

1970-01-01 00:00:25 Error D004.3 ToD request sent- No Response received
1970-01-01 00:00:25 Notice I401.0 TLV-11 - unrecognized OID
1970-01-01 00:00:22 Error D004.3 ToD request sent- No Response received
1970-01-01 00:00:21 Critical D003.0 DHCP WARNING - Non-critical field invalid in response.

Because i dont have certificat i have stay BPI : disable.

If anyone can help me, it will be very great

Thank you for everyone and accept my best regards

[drewmerc]

ToD errors are not important
unrecognized OID could be that your mac does not match your spoof

you have a certificate it's just not a valid one (this still means you have to try the other bpi settings)

[zarkocg68]

Hello mate,

I have testing every BPI mode and here the log :


[u]BPI DOcsis1.0

1970-01-01 00:00:28 Error D004.3 ToD request sent- No Response received
1970-01-01 00:00:27 Notice I401.0 TLV-11 - unrecognized OID


BPI + Docsis1.1

1970-01-01 00:00:37 Error B301.8 Auth Reject - Permanent Authorization Failure
1970-01-01 00:00:37 Notice I401.0 TLV-11 - unrecognized OID
1970-01-01 00:00:12 Critical R002.0 No Ranging Response received - T3 time-out (US 2)
1970-01-01 00:00:04 Notice M571.1 Ethernet link up - ready to pass packets


BPI + Bypass

1970-01-01 00:00:25 Critical I001.0 REG-RSP - invalid format or not recognized
1970-01-01 00:00:25 Notice I401.0 TLV-11 - unrecognized OID

BPI Disabled :

1970-01-01 00:00:23 Notice I401.0 TLV-11 - unrecognized OID


For the MAC adress, i have stay the Modem serial, MAC adress Modem, and MAC Ethernet adress from my original modem. ONLY the USB modem MAC ADRESS dont have stay from my original because i dont know where i can find this adress. Because i dont have stay USB MAC Adress from my first modem, may be for that dont want to work ????

For sure, i have turn off my first modem when i test my modem with haxorware ....

And for other information i dont have sending in modem config file, because i dont k[/u]now what is it and if he necesary ????

And an other information. From when i have flashing the modem with haxorware, the light : CABLE, SEND DATA And Power ARE ALWAYS ON !?! Cable are ON and when the coax. cable is UNPLUGED ? it is normal ??

My best regards and thank you for your help in advance.

[drewmerc]

whats the software version of your original modem (it's under the help tab)
i am guessing it's this mac your using



as it has to match what is in haxor (random pics, yes i know they dont match)

[zarkocg68]

Thank you for your response.

I have in modem indentifier, vendor, model, version software, typing the same infos of my original.

Original version software of my modem is : v2.0.2r1256-060303

you have get +1 rep of me for your help and patience. ..

[drewmerc]

this is how your spoof should be (i hope it is)

   

now what does your error log say and can you get online

[zarkocg68]

THXS for your message.

I have stay exactly the same infos of your picture in attachment.

In log :

Event Log
Time Priority Code Description
1970-01-01 00:00:26 Notice I401.0 TLV-11 - unrecognized OID


when i stay bpi+ i got in log :

1970-01-01 00:00:31 Error B301.8 Auth Reject - Permanent Authorization Failure
1970-01-01 00:00:31 Notice I401.0 TLV-11 - unrecognized OID

And i need to say that i have not uploaded any certificat . May be for that do not work ????

[drewmerc]

yep i'm guessing your going to need certs but with luck that should be easy depending on how you want to do this

1 quickest and easyest buy/build a jtag and dump the nonvol from you original modem
2 not as easy as 1 but buy/build a max cable and load haxorware into ram and dump the nonvol
3 hard but no buy/build, use the webby firm upgrade page to flash the signed ambit250 shelled firmware and the use that to flash haxor and use that to dump the nonvol

[zarkocg68]

i be liked 3. )))

[drewmerc]

just noticed this it should help you (number 3)

First install The program net-snmp-5.4.2.1.win32 Add in the rar.
Make sure that the Firmware is called "haxorware.bin" Copy the Firmware that is in this rar or change the name of your bin file for (haxorware.bin) And add to the TFTP Folder.
Download Here:
  DPC2100R2 Without Cables.rar (Size: 4.51 MB / Downloads: 4,500)

This method works in the Modem Webstar DPC2100R2 or EPC2100R2 With the firmware ver: v202r1256-060303, Not in the DPC2100
Edited: 07-13-2010 Works in a DPC2100 i did it!!!

SET UP TCP/IP:
192.168.100.10
255.255.255.0
192.168.100.1

1. Install net-snmp-5.4.2.1.win32!!!!

2. Open your TFTP server and be sure that the haxorware.bin is in the Folder:





2. Just open The DPC2100R2.bat File and follow the intructions is very easy When You see that the TFTP Server
Finish Sending the bin file wait 5 seconds and reboot the modem!!
And Enjoy Haxorware.





NOTE:
For this method work you need to install First net-snmp-5.4.2.1.win32 add in the folder
And that the TFTP is Ready to Sent the bin File called (haxorware.bin) add in the folder is the last version haxorware11rev39-DIAG.bin


taken from here http://www.sbhacker.net/forum/index.php/...one-click/