Does anyone have any firmware without certs?

[occalifornia]

What is the Tuner CFG and PGA Type for SB6141 VERSION 8 with Forceware 1.4 ?

The same. set auto config to sb6141 and hit apply. you'll see the tuner/pga on the bottom updated for you.

Thanks, I did try it but it looks like for VERSION 8, the default Tuner CFG = MXL261 x2 and the PGA Type = MT1570 does not work. It cannot lock into channels.

Continues to work fine for me. You could fail to lock channels for other reasons.

[Ictvtec]

Did u try to see if stock firmware locks on??

What is the Tuner CFG and PGA Type for SB6141 VERSION 8 with Forceware 1.4 ?

The same. set auto config to sb6141 and hit apply. you'll see the tuner/pga on the bottom updated for you.

Thanks, I did try it but it looks like for VERSION 8, the default Tuner CFG = MXL261 x2 and the PGA Type = MT1570 does not work. It cannot lock into channels.

[legendofsounds]

Did u try to see if stock firmware locks on??

What is the Tuner CFG and PGA Type for SB6141 VERSION 8 with Forceware 1.4 ?

The same. set auto config to sb6141 and hit apply. you'll see the tuner/pga on the bottom updated for you.

Thanks, I did try it but it looks like for VERSION 8, the default Tuner CFG = MXL261 x2 and the PGA Type = MT1570 does not work. It cannot lock into channels.

id stay away from v8 modems specially the white ones if using forceware on them... just saying

[occalifornia]

Did u try to see if stock firmware locks on??

What is the Tuner CFG and PGA Type for SB6141 VERSION 8 with Forceware 1.4 ?

The same. set auto config to sb6141 and hit apply. you'll see the tuner/pga on the bottom updated for you.

Thanks, I did try it but it looks like for VERSION 8, the default Tuner CFG = MXL261 x2 and the PGA Type = MT1570 does not work. It cannot lock into channels.

id stay away from v8 modems specially the white ones if using forceware on them... just saying

why?

[McAdams]

Did u try to see if stock firmware locks on??

The same. set auto config to sb6141 and hit apply. you'll see the tuner/pga on the bottom updated for you.

Thanks, I did try it but it looks like for VERSION 8, the default Tuner CFG = MXL261 x2 and the PGA Type = MT1570 does not work. It cannot lock into channels.

id stay away from v8 modems specially the white ones if using forceware on them... just saying

why?

x2?

[vbhxdnfk]

Forceware T3-timeout occur to me on the SB6141 rev:4 ,Hardware Version: 8.0

It can lock the channel,but it can not send out data from Upstream,even the power level is displayed to 58dBv,then T3-timeout.

Model Name: SB6141
Vendor Name: Motorola
Firmware Name: SB_KOMODO-1.0.6.14-SCM03-NOSH
Boot Version: PSPU-Boot(25CLK)(W) 1.0.12.18m5
Hardware Version: 8.0
Firmware Build Time: Jan 22 2015 14:31:03

[occalifornia]

Forceware T3-timeout occur to me on the SB6141 rev:4 ,Hardware Version: 8.0
It can lock the channel,but it can not send out data from Upstream,even the power level is displayed to 58dBv,then T3-timeout.
Model Name: SB6141
Vendor Name: Motorola
Firmware Name: SB_KOMODO-1.0.6.14-SCM03-NOSH

Is forceware built upon that SB_KOMODO build or is that from your stock modem?

Your upstream power level seems way too high.

http://www.scte.org/TechnicalColumns/06-...levels.pdf

[vbhxdnfk]

Forceware T3-timeout occur to me on the SB6141 rev:4 ,Hardware Version: 8.0
It can lock the channel,but it can not send out data from Upstream,even the power level is displayed to 58dBv,then T3-timeout.
Model Name: SB6141
Vendor Name: Motorola
Firmware Name: SB_KOMODO-1.0.6.14-SCM03-NOSH

Is forceware built upon that SB_KOMODO build or is that from your stock modem?

Your upstream power level seems way too high.

http://www.scte.org/TechnicalColumns/06-...levels.pdf

I have collected those information when SB6141 was a virgin.

[occalifornia]

Forceware T3-timeout occur to me on the SB6141 rev:4 ,Hardware Version: 8.0
It can lock the channel,but it can not send out data from Upstream,even the power level is displayed to 58dBv,then T3-timeout.
Model Name: SB6141
Vendor Name: Motorola
Firmware Name: SB_KOMODO-1.0.6.14-SCM03-NOSH

Is forceware built upon that SB_KOMODO build or is that from your stock modem?

Your upstream power level seems way too high.

http://www.scte.org/TechnicalColumns/06-...levels.pdf

I have collected those information when SB6141 was a virgin.

That can't be true because a 6141 doesn't come 'virgin' with forceware firmware..

[vbhxdnfk]

Forceware T3-timeout occur to me on the SB6141 rev:4 ,Hardware Version: 8.0
It can lock the channel,but it can not send out data from Upstream,even the power level is displayed to 58dBv,then T3-timeout.
Model Name: SB6141
Vendor Name: Motorola
Firmware Name: SB_KOMODO-1.0.6.14-SCM03-NOSH

Is forceware built upon that SB_KOMODO build or is that from your stock modem?

Your upstream power level seems way too high.

http://www.scte.org/TechnicalColumns/06-...levels.pdf

I have collected those information when SB6141 was a virgin.

That can't be true because a 6141 doesn't come 'virgin' with forceware firmware..

I supposed that 'virgin' refers to official firmware...
I mean the official firmware loaded on SB6141 when I bought it.