total newbie sb5102/ sb 5101

[justsomeguy]

hello everyone....i really hope i don't get flammed to badly on this question...letme start by saying that i'm a totall newbie here and am trying to read read read until my eyeballs bleed...and i hope this isn't too stupid of a question although i'm sure it is....

i've downloaded the posted sb51o2 script that was posted..and i know that you have to change the mac address to one that isn't in your area....basically i just got my usbjtag and am trying to figure out everything i've been reading and actually now have the tools to be able to look at things while i'm reading and try to figure shit out....so i also have a sb5102 on hand that i'm also gonna be testing...so i still have to change the mac from the one that's been downloaded in the file right? cause that one is from who know's where right? and morre the deffently not frorm my city up north in canada....but as i'm looking at a bunch of garble that i don't really understand cause i'm not a programmer nor am i very good at codeing...but where would i change that mac? i'm using the usbjtag nt software which is provided at another site ...now i know you have to put the haxowarre on it as well (which i havn't played with yet)..do you have to do this first? then put it into the haxoware? and if so do you have to do this in the code in notepad or is there a nice user friendly place to put it in a software progream.....

and again i'm really really sorry if this is a dumbass question, and i do expect to get flammed for it..but hey everyone was a nubie at one time right !!! and even though i'm not a programmin wiz but I am trying to figure stuff out and do indeed love testing (as i've tested sat's for years) and have been reading and reading...i know this is a whole different ballpark then sats..but i'd love a little push in the right direction here...sorry for being so long winded and i hope to have a little help if you guys don't mind...

thanks ever so much .....
i'm sure as i go along i'll have more dumbass questions just so you know....hahahah
***i also have a sb5101 that i'm gonna use for testing..***
justsomeguy

[drewmerc]

tldr: canada are you on rogers
take 1 subbed 5102 modem on a different node take a full dump(2mb) and put it on your modem

[justsomeguy]

tldr: canada are you on rogers
take 1 subbed 5102 modem on a different node take a full dump(2mb) and put it on your modem

no rogers here...only shaw...but if i can't find someone with a 5102 i can just snigg out some macs and use them right????

[drewmerc]

shaw may be different (i'm not fin canada but rogers are fuckers for there certs)
flash it whit haxor and stick a mac on and see if it goes online (take a full dump first)

[justsomeguy]

shaw may be different (i'm not fin canada but rogers are fuckers for there certs)
flash it whit haxor and stick a mac on and see if it goes online (take a full dump first)

I'm sure this will sound totally stupid and totally newbie !!! but can i edit the haxoware with the usbjtag software? i downloaded the haxoware but there this no user interface with it so i'm a bit lost...although i'm still in the reading process i have a long way to go still....again and again and again i'm sorry for the stupid questions !!!! and are you sure i can just put my 14 pin usbjtag nt in the 10 pins? there doesn't seem to be a good connection and they kinda stick up a bit cause there's the board that the extra pins are sitting on top of..

edit..k i found part of my question...you have to use a software program like usbjtag's to put the haxoware in it...now i still have to add a valid mac right? is this done in notepad or the same prg? is there a certain code i have to put in in order to do this?..sorry for all the questions..i find that reading, asking, then reading more helps me out a lot !!!

edit again...figure i might as well keep all this in the same thread...so i think my problem mybe that i have a 14 pin usbjtag nt and the board on the sb5101 has only 10 holes !! i tried to put the jtag in it and just let the other 4 pins sit on top of the board but it doesn't seem to see it at all....tried to detect it and nothing...does the pins have to be sodered in there or can they just sit in the holes? i've tried to put the pins each way in the holes on both the front and back of the board..remember i'm a totally dumbass newbie at this...but i'm trying hard and willing to learn....thanks guys and gals...

[drewmerc]

http://usbjtag.com/jtagnt/sb5102.php
http://www.sbhacker.net/forum/index.php/...-tutorial/
sb5102 not an easy modem to start with but good luck

[justsomeguy]

http://usbjtag.com/jtagnt/sb5102.php
http://www.sbhacker.net/forum/index.php/...-tutorial/
sb5102 not an easy modem to start with but good luck

well i also have sb5101 if that's easier !!!

keep trying the sbhacker site but can never get in...damn..just my luck...lol

[drewmerc]

5101 easy
http://www.usbjtag.com/jtagdevices/sb5101.php
hook it up as the pic shows (pin 1 matching and you only use the first 10 dont worry about the rest)
then follow the 5100 to dump and flash

[justsomeguy]

5101 easy
http://www.usbjtag.com/jtagdevices/sb5101.php
hook it up as the pic shows (pin 1 matching and you only use the first 10 dont worry about the rest)
then follow the 5100 to dump and flash

so i was about to attempt this modem last night and was on a mirc line and someone told me that because my only isp is shaw that i cannot do this the normal way?? is this true? anyone know?? man o man..just my luck...lol

[rajkosto]