+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: who can help me? hurry!!! (/showthread.php?tid=2845)
who can help me? hurry!!! - ndk2000 - 16-11-2013
Found energy at frequency 754000000Hz! Publishing event kEventEnergyDetected...
0x0000641e [CmDocsisCtlThread] BcmCmDocsisCtlThread::StartUsInit: (CmDocsisCtlThread) Locked on the downstream.
Waiting for UCDs...
******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 754000000 Hz
Carrier Offset = 36 Hz
Symbol rate = 6952000 sym/sec
SNR = 34 dB
QAM Mode = QAM256
Tuner AGC = 0xfff00000
IF AGC = 0x189eaf9d
Power Level = -9 dB
QAM = LOCKED
FEC = LOCKED
******************************************
Calculating maximum number of IP filters:
Each IP filter consumes 1840 bytes of RAM.
Current free RAM is 465284 bytes.
Max heap reserved for IP filters (25%) = 116321
We can support 63 IP filters.
Calculating maximum number of LLC filters:
Each LLC filter consumes 724 bytes of RAM.
Current free RAM is 465284 bytes.
Max heap reserved for LLC filters (25%) = 116321
We can support 160 LLC filters.
CM> Selecting UCD for Us Channel 4
0x00006c0c [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchDsTimeSync: (CmDocsisCtlThread) starting ds time
sync acquisition...
0x00006e82 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) downstream time sync
acquired...
0x00006e8c [CmDocsisCtlThread] BcmCmDocsisCtlThread:
sSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 46.0 dBmV
0x00006e8c [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) rx unexpected kDsSyncOk
indication...
Not logging event ID 2307948724, control for level 7 is 0.
RNG-RSP Adj: tim=777 power=0 freq=0 Stat=Continue
CM> 0x00007378 [DHCP Server Thread] BcmDhcpServerThread::ThreadMain: (DHCP Server Thread) Callback request
expired:
timerDuration secs = 1
current time secs = 29
elapsed time secs = 1
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Success
******************************************
UPSTREAM STATUS
******************************************
Upstream Status = UP
Upstream Channel = 4
Upstream Frequency = 45000000 Hz
Upstream Power = 47 dBmV
Ranging SID = 0x23d
Upstream Symbol Rate = 2560000 sym/sec
******************************************
Starting IP Initialization with DHCP...
DHCPc: Waiting 2 seconds before sending Discover; client id htype=1, value=24:76:7d:07:a2:ba
Not logging event ID 2307948624, control for level 7 is 0.
CM> DHCPc: Sending Discover packet; client id htype=1, value=24:76:7d:07:a2:ba
DHCPc: Received an Offer from DHCP server 00:23:5e:70:11:d9 (10.38.0.1); lease client id htype=1,
value=24:76:7d:07:a2:ba
CM> DHCPc: Timed out waiting for offers for lease with client id htype=1, value=24:76:7d:07:a2:ba
DHCPc: Sending Request packet; client id htype=1, value=24:76:7d:07:a2:ba
DHCPc: Received an Ack from DHCP server 00:23:5e:70:11:d9 (10.38.0.1); lease client id htype=1,
value=24:76:7d:07:a2:ba
Current IP address is default 0.0.0.0.
0x000085ac [DHCP Client Thread] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack1 HalIf)
Configuring IP stack 1:
IP Address = 10.38.231.173 (primary IP address)
Subnet Mask = 255.255.0.0
Router = 10.38.0.1
IsPrimaryInterface = 1
Logging event: DHCP WARNING - Non-critical field invalid in response.
ARPing for default GW IP = 10.38.0.1
MAC = 00:23:5e:70:11:d9
DHCP completed successfully!
DHCP Settings:
Client Id = htype=1, value=24:76:7d:07:a2:ba
State = Renewing (5)
Static Lease = 0
AutoConfig Mode = IP, Subnet and Router
XID = 0x62826508
Number of Tries = 0
Max Discover Tries = 6
Max Request Tries = 6
DHCP server MAC addr = 00:23:5e:70:11:d9
Ignore NAKs = 0
My offered IP address = 10.38.231.173 (primary IP address)
(1) Subnet Mask = 255.255.0.0
(3) Router IP address = 10.38.0.1
(54) DHCP Server IP address = 172.19.255.8
(82) Relay Agent IP address = 10.38.0.1
TFTP Server IP address = 10.38.0.1
CM Configuration file = 'xv9873254k;fg87dsfd;'
(2) UTC Time Offset = 0 seconds
(4) Time Server IP address = 172.19.255.121
(6) Domain Name Server = 211.137.241.34; 211.137.241.35
(7) Log Server IP address =
(51) Lease time = 6000 seconds
(58) T1 (renew) = 3000 seconds
(59) T2 (rebind) = 5700 seconds
Lease is infinite = 0
SB5102 CM Agent w/ BRCM Factory Support IpStackEvent: Ip=10.38.231.173, Subnet=255.255.0.0, Gateway=10.38.0.1
CmSnmpAgent::IpAddressAcquiredEvent for SB5102 CM Agent w/ BRCM Factory Support
IP addr = 10.38.231.173
Starting Time Of Day...
0x00008642 [CmDocsisIpThread] BcmDocsisTimeOfDayThread::SetTodServerIpAddress: (Time Of Day Thread) ToD servers:
172.19.255.121
Connecting to ToD server 172.19.255.121...
Sending UDP ToD request to server...
SNMP Agent Binding to 10.38.231.173:225
Not logging event ID 2291949724, control for level 7 is 0.
CM> 0x0000873c [Time Of Day Thread] BcmDocsisTimeOfDayThread::HandleToD: (Time Of Day Thread) WARNING - Timed out
waiting for a response from the ToD server.
Waiting 2000 ms before trying this server again...
Logging event: ToD request sent- No Response received
Starting Tftp of configuration file...
Opening file 'xv9873254k;fg87dsfd;' on 10.38.0.1 for reading...
tftp-enforce bypass is DISABLED
TFTPD Started
Forcing Config TFTP IP to 127.0.0.1
Forcing Config File name to dsfd;kfoA,.iyewrkldJ
TFTPD received 1 from 10.38.231.173:1027
Storing received cfg of size 4585 to memory
TFTPD Shut down
Tftp read < 512 bytes, we have reached end of file.
Tftp transfer complete!
TFTP Settings:
Stack Interface = 1
Server Ip Address = 10.38.0.1
Server Port Number = 1029
Total Blocks Read = 9
Total Bytes Read = 4585
Config file was read! IP Initialization completed...
MAX CPE per CM is being set to 32
TLV-11[1]: 1.3.6.1.2.1.69.1.6.3.0 -> 2 (i32)
TLV-11[2]: 1.3.6.1.2.1.69.1.6.4.1.5.17 -> 3 (i32)
TLV-11[211]: 1.3.6.1.2.1.69.1.6.4.1.11.24 -> 17 (i32)
Connecting to ToD server 172.19.255.121...
Sending UDP ToD request to server...
Not logging event ID 2291949524, control for level 7 is 0.
SB5102 CM Agent w/ BRCM Factory Support processing TLV-11's
SNMP packet sent to 10.38.231.173:225
Insufficient heap to handle SNMP packet - TOO_BIG.
(PDU = 250212, heap = 231136)
TLV-11 failure: error status=1, error index=0
Invalid TLV-11's: 1 wrong values, 0 duplicate sets.
SNMP Error'd but Haxorware doesn't care AT ALL!
Onwards mateys!
Sending a REG-REQ to the CMTS...
Logging event: TLV-11 - Illegal Set operation failed
NonVolDeviceDriver::NonVolDriverWrite: WARNING - Current segment size < buffer size! Increasing the segment size!
Received a REG-RSP message from the CMTS...
0x00009894 [CmDocsisCtlThread] BcmCmDocsisCtlThread::RegRspMsgEvent: (CmDocsisCtlThread) We registered with a
DOCSIS 1.1 config file!
Registration complete!
Process CVC
0x000098a8 [CmDocsisCtlThread] CmSecureDownload:
rocessConfigFileManufAndCosignerCvcs: (Secure Software Download) WARNING - No CVC included in config file; software upgrade can't be performed!
0x000098a8 [CmDocsisCtlThread] BcmCmDocsisCtlThread:
rocessCVC: (CmDocsisCtlThread) ERROR - Config file does not include a valid CVC!
DOCSIS CoS/QoS rate shaping enable is now 1
CmSnmpAgent::CmOperationalEvent for SB5102 CM Agent w/ BRCM Factory Support
CmSnmpAgent operating in 1.1 mode, including docsQos, excluding docsBpi
+++ No DH kickstart profiles or snmpCommunityTable entries installed.
We will operate in NMACCESS mode.
SB5102 CM Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
SB5102 CM Agent w/ BRCM Factory Support enabling management.
SB5102 CM Agent w/ BRCM Factory Support sending deferred traps...
Done w/ deferred traps.
SB5102 CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
0x000098b2 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchBpkm: (CmDocsisCtlThread) BPKM disabled via
manufacturing setting.
Enabling network access for all CPE ports.
mot_scanList: Writing to Flash!
BcmCmDocsisStatusEventCodes::kCmIsOperational
Suspending SNMP Thread
0x00009b14 [CmDocsisCtlThread] BcmVendorCmApplication::StopDhcpServer: (VendorExtension CmApp) Shutting down DHCP
Server...
0x00009b14 [CmDocsisCtlThread] BcmStandbySwitchThread::CmIsOperational: (Motorola Standby Switch Thread)
Simulating a press of the standby switch to get the state configured properly.
0x00009b1e [Time Of Day Thread] BcmDocsisTimeOfDayThread::HandleToD: (Time Of Day Thread) WARNING - Timed out
waiting for a response from the ToD server.
Waiting 2000 ms before trying this server again...
0x00009b1e [IGMP Thread] BcmIgmpThread::Starting Igmp Thread...: (IGMP Thread)
0x00009b1e [Motorola Standby Switch Thread] BcmStandbySwitchThread::ThreadMain: (Motorola Standby Switch Thread)
Standby switch was pressed!
0x00009b1e [Motorola Standby Switch Thread] BcmStandbySwitchThread:
rocessSwitchEvent: (Motorola Standby Switch Thread) Standby switch disabled in nonvol; ignoring event.
Non-Vol Settings successfully written to the device.
SB5102 CM Event Log w/ BRCM Factory Support sending deferred async messages...
Done w/ deferred msgs
Not logging event ID 2296948624, control for level 7 is 0.
Logging event: ToD request sent- No Response received
CM> Connecting to ToD server 172.19.255.121...
Sending UDP ToD request to server...
0x0000a3e8 [Time Of Day Thread] BcmDocsisTimeOfDayThread::HandleToD: (Time Of Day Thread) WARNING - Timed out
waiting for a response from the ToD server.
Waiting 2000 ms before trying this server again...
Logging event: ToD request sent- No Response received
CM> 0x0000abb8 [Time Of Day Thread] BcmDocsisTimeOfDayThread::HandleTod: (Time Of Day Thread) WARNING - Exceeded
max number of ToD retries for all servers. Waiting for period timer to expire...
CM>
i define the config file name and ip, but they not work
now its limited 200k! its useless
please tell me why and how can i fix it?
have any way to solve this?
thank you everybody help me!!!
RE: who can help me? hurry!!! - drewmerc - 16-11-2013
same answer as every other damn fucking post you have made
stop forcing the fucking config, leave it blank and take the one you are served