+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: stuck at Starting IP Initialization with DHCP... (/showthread.php?tid=2779)
stuck at Starting IP Initialization with DHCP... - ndunpeal - 24-09-2013
Hello,
Can someone tell me what is wrong with my telnet log and event log, its just stuck at Starting IP Initialization with DHCP... and reboot after some time or scan again. What i am missing?
Epc2100R2 my isp is on D1.0.
Haxorware integrated telnet daemon
Username: root
Password: ****
Welcome.
CM>
CM> run_app
Running the system...
CM> Non-Vol Settings successfully written to the device.
@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
mot_scanList: Setting override freq @ 7000000
Scanning DS Channel at 7000000 Hz... (Initial target freq)
mot_scanList: Setting override freq @ 0
Favorite[1].freq = 730000000
Attempting Downstream FEC lock @ freq= 730000000 Hz, QAM64/256
Favorite[2].freq = 746000000
Attempting Downstream FEC lock @ freq= 746000000 Hz, QAM64/256
******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 746000000 Hz
Carrier Offset = -18 Hz
Symbol rate = 6952000 sym/sec
SNR = 35 dB
QAM Mode = QAM256
Tuner AGC = 0xfff00000
IF AGC = 0x1668cb22
Power Level = -2 dB
QAM = LOCKED
FEC = LOCKED
******************************************
CM> Non-Vol Settings successfully written to the device.
@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
mot_scanList: Setting override freq @ 658000000
Scanning DS Channel at 658000000 Hz... (Initial target freq)
******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 658000000 Hz
Carrier Offset = -15 Hz
Symbol rate = 6952000 sym/sec
SNR = 42 dB
QAM Mode = QAM256
Tuner AGC = 0xfff00000
IF AGC = 0x1331ca7e
Power Level = 11 dB
QAM = LOCKED
FEC = LOCKED
******************************************
CM> Selecting UCD for Us Channel 4
RNG-RSP Adj: tim=2472 power=28 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Success
******************************************
UPSTREAM STATUS
******************************************
Upstream Status = UP
Upstream Channel = 4
Upstream Frequency = 45180000 Hz
Upstream Power = 41 dBmV
Ranging SID = 0x1082
Upstream Symbol Rate = 2560000 sym/sec
******************************************
Starting IP Initialization with DHCP...
CM>
Event Log:
1970-01-01 00:01:25 Critical D001.0 DHCP FAILED - Discover sent, no offer received
1970-01-01 00:01:11 Critical R002.0 No Ranging Response received - T3 time-out (US 4)
1970-01-01 00:01:05 Notice M572.0 T1 No Ucd Timeout - Reinitialize MAC...
1970-01-01 00:01:05 Critical U001.0 No UCD's Received - Timeout
1970-01-01 00:00:54 Critical T002.0 SYNC Timing Synchronization failure - Failed to acquire FEC framing
1970-01-01 00:00:20 Critical D001.0 DHCP FAILED - Discover sent, no offer received
1970-01-01 00:00:09 Critical R002.0 No Ranging Response received - T3 time-out (US 4)
1970-01-01 00:00:06 Notice M571.1 Ethernet link up - ready to pass packets
1970-01-01 00:00:56 Notice M573.0 Modem Is Shutting Down and Rebooting...
1970-01-01 00:00:56 Critical Resetting the cable modem due to docsDevResetNow
Thank you in advance
RE: stuck at Starting IP Initialization with DHCP... - ABMJR - 24-09-2013
Thats a Lite log, flash diag and then post a log