Haxorware Forums
I'm trying to get a telnet log - Printable Version

+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: I'm trying to get a telnet log (/showthread.php?tid=2493)



I'm trying to get a telnet log - therealdeal - 15-04-2013

Hello everyone i'm not exactly new to this but I need to keep learning and find more information about everything that's going on especially after certificate and BPI + security stuff.

ok so I usually just go to my cmd (command prompt) then I telnet into my SB5101 using haxorware

telnet 192.168.100.1
then type root as the user name and password admin. fine it goes into it without problems... however there are a lot of commands I am not familiar with. I've been playing around using help already but I just want to know how to properly create the haxorware telnet log to troubleshoot and what not. I am getting the CVC valiadation failure on my modem and I understand that haxorware log is not enough therefore I am doing what the pros are doing trying to learn the right way. let me know if someone can help me or point me into the right direction. Thank you.

Big Grin
Well i'm trying to ask if I am getting into the telnet correctly. and how to give it a command that will create a telnet log. Can anyone help me.


RE: I'm trying to get a telnet log - drewmerc - 15-04-2013

http://www.haxorware.com/forums/thread-1888-post-13288.html#pid13288


RE: I'm trying to get a telnet log - therealdeal - 15-04-2013

WOW thanks i will give it a shot once i get a chance. I think i will definately do method 2. How do you usually do it?
(15-04-2013, 06:26 PM)drewmerc Wrote: http://www.haxorware.com/forums/thread-1888-post-13288.html#pid13288



RE: I'm trying to get a telnet log - therealdeal - 18-04-2013

Great thank you very much for your very informative post. I have now successfully Created a telnet log using method 2 (via Putty). Now i am hopefully one step closer to finding out the solution to a bigger problem. anyways, heres the telnet log and i get a TWC provision page any hints or guides some one can point me out to? What exactly causes this problem? I know i am getting what they called a walgarden config (its probably that) any one has a solution to this?


heres the Telnet log extracted via Putty:

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.04.18 12:33:40 =~=~=~=~=~=~=~=~=~=~=~=
Haxorware integrated telnet daemon

Username: root
Password: *****
Welcome.

CM>
CM> run
CM>
CM> run_app


Running the system...


Beginning Cable Modem operation...

0x0003f9b2 [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Scanning for a Downstream Channel...

mot_scanList: Setting override freq @ 0
Favorite[0].freq = 297000000
Attempting Downstream FEC lock @ freq= 297000000 Hz, QAM64/256

CM> \Found energy at frequency 297000000Hz! Publishing event kEventEnergyDetected...
0x0003fc00 [CmDocsisCtlThread] BcmCmDocsisCtlThread::StartUsInit: (CmDocsisCtlThread) Locked on the downstream. Waiting for UCDs...

******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 297000000 Hz
Carrier Offset = -1 Hz
Symbol rate = 5360537 sym/sec
SNR = 36 dB
QAM Mode = QAM256
Tuner AGC = 0xfff00000
IF AGC = 0x163ec5a1
Power Level = -4 dB
QAM = LOCKED
FEC = LOCKED
******************************************

Calculating maximum number of IP filters:
Each IP filter consumes 1836 bytes of RAM.
Current free RAM is 430280 bytes.
Max heap reserved for IP filters (25%) = 107570
We can support 58 IP filters.
Calculating maximum number of LLC filters:
Each LLC filter consumes 724 bytes of RAM.
Current free RAM is 430280 bytes.
Max heap reserved for LLC filters (25%) = 107570
We can support 148 LLC filters.

CM> \Selecting UCD for Us Channel 2

0x00040416 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchDsTimeSync: (CmDocsisCtlThread) starting ds time sync acquisition...
0x000404a2 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) downstream time sync acquired...
0x000404a2 [CmDocsisCtlThread] BcmCmDocsisCtlThread:Big GrinsSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 45.0 dBmV
0x000404a2 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) rx unexpected kDsSyncOk indication...
Not logging event ID 2307948724, control for level 7 is 0.

CM> \
RNG-RSP Adj: tim=1426 power=-6 freq=0 Stat=Continue

CM> \
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue

CM> \
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue

CM> \
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue

CM> \
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Success

******************************************
UPSTREAM STATUS
******************************************
Upstream Status = UP
Upstream Channel = 2
Upstream Frequency = 23800000 Hz
Upstream Power = 44 dBmV
Ranging SID = 0x1897
Upstream Symbol Rate = 5120000 sym/sec
******************************************

Starting IP Initialization with DHCP...
DHCPc: Waiting 3 seconds before sending Discover; client id htype=1, value=00:14:e8:25:91:34
Not logging event ID 2307948624, control for level 7 is 0.

CM> \DHCPc: Sending Discover packet; client id htype=1, value=00:14:e8:25:91:34
DHCPc: Received an Offer from DHCP server 00:15:f9:2a:21:f1 (10.39.96.1); lease client id htype=1, value=00:14:e8:25:91:34

CM> \DHCPc: Timed out waiting for offers for lease with client id htype=1, value=00:14:e8:25:91:34
DHCPc: Sending Request packet; client id htype=1, value=00:14:e8:25:91:34
DHCPc: Received an Ack from DHCP server 00:15:f9:2a:21:f1 (10.39.96.1); lease client id htype=1, value=00:14:e8:25:91:34
Current IP address is default 0.0.0.0.
0x00042bbc [DHCP Client Thread] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack1 HalIf)
Configuring IP stack 1:
IP Address = 10.39.121.245 (primary IP address)
Subnet Mask = 255.255.224.0
Router = 10.39.96.1
IsPrimaryInterface = 1

Logging event: DHCP WARNING - Non-critical field invalid in response.
ARPing for default GW IP = 10.39.96.1
MAC = 00:15:f9:2a:21:f1
DHCP completed successfully!

DHCP Settings:
Client Id = htype=1, value=00:14:e8:25:91:34
State = Renewing (5)
Static Lease = 0
AutoConfig Mode = IP, Subnet and Router
XID = 0x2cab8c41
Number of Tries = 0
Max Discover Tries = 6
Max Request Tries = 6
DHCP server MAC addr = 00:15:f9:2a:21:f1
Ignore NAKs = 0
My offered IP address = 10.39.121.245 (primary IP address)
(1) Subnet Mask = 255.255.224.0
(3) Router IP address = 10.39.96.1
(54) DHCP Server IP address = 24.29.137.53
(82) Relay Agent IP address = 10.39.96.1
TFTP Server IP address = 24.29.158.48
CM Configuration file = '?BBgdiTUAFOglkTQKJ3n1@Cid59TarFSmSIKIj+GFt_lVNYDxIZxfs'
(2) UTC Time Offset = -18000 seconds
(4) Time Server IP address = 24.29.158.48
(6) Domain Name Server = 209.18.47.61; 209.18.47.62
(7) Log Server IP address = 24.29.99.57
(51) Lease time = 910582 seconds
(58) T1 (renew) = 455291 seconds
(59) T2 (rebind) = 796759 seconds
Lease is infinite = 0


SB5102 CM Agent w/ BRCM Factory Support IpStackEvent: Ip=10.39.121.245, Subnet=255.255.224.0, Gateway=10.39.96.1
CmSnmpAgent::IpAddressAcquiredEvent for SB5102 CM Agent w/ BRCM Factory Support
IP addr = 10.39.121.245
Starting Time Of Day...
0x00042c48 [CmDocsisIpThread] BcmDocsisTimeOfDayThread::SetTodServerIpAddress: (Time Of Day Thread) ToD servers: 24.29.158.48
Connecting to ToD server 24.29.158.48...
Sending UDP ToD request to server...
SNMP Agent Binding to 10.39.121.245:225
Not logging event ID 2291949724, control for level 7 is 0.

CM> \UTC returned by ToD server 3575291471; UTC offset -18000
Current system time -> Thu Apr 18 11:31:11 2013

System start time -> Thu Apr 18 11:26:38 2013

Starting Tftp of configuration file...
Opening file '?BBgdiTUAFOglkTQKJ3n1@Cid59TarFSmSIKIj+GFt_lVNYDxIZxfs' on 24.29.158.48 for reading...
tftp-enforce bypass is DISABLED
Storing received cfg of size 3387 to memory
Tftp read < 512 bytes, we have reached end of file.
Tftp transfer complete!
TFTP Settings:
Stack Interface = 1
Server Ip Address = 24.29.158.48
Server Port Number = 40249
Total Blocks Read = 7
Total Bytes Read = 3387

Config file was read! IP Initialization completed...
MAX CPE per CM is being set to 32
TLV-11[1]: 1.3.6.1.2.1.69.1.2.1.2.16 -> 255.255.255.255
TLV-11[2]: 1.3.6.1.2.1.69.1.2.1.3.16 -> 255.255.255.255
TLV-11[3]: 1.3.6.1.2.1.69.1.2.1.4.16 -> RR_nycmny_nyc_m0d3m5
TLV-11[4]: 1.3.6.1.2.1.69.1.2.1.5.16 -> 3 (i32)
TLV-11[5]: 1.3.6.1.2.1.69.1.2.1.6.16 -> HEX:40 00
TLV-11[6]: 1.3.6.1.2.1.69.1.2.1.7.16 -> 4 (i32)
TLV-11[7]: 1.3.6.1.2.1.69.1.2.1.2.18 -> 255.255.255.255
TLV-11[8]: 1.3.6.1.2.1.69.1.2.1.3.18 -> 255.255.255.255
TLV-11[9]: 1.3.6.1.2.1.69.1.2.1.4.18 -> yZaK4E8l
TLV-11[10]: 1.3.6.1.2.1.69.1.2.1.5.18 -> 2 (i32)
TLV-11[11]: 1.3.6.1.2.1.69.1.2.1.6.18 -> HEX:40 00
TLV-11[12]: 1.3.6.1.2.1.69.1.2.1.7.18 -> 4 (i32)
TLV-11[13]: 1.3.6.1.2.1.69.1.2.1.2.19 -> 255.255.255.255
TLV-11[14]: 1.3.6.1.2.1.69.1.2.1.3.19 -> 255.255.255.255
TLV-11[15]: 1.3.6.1.2.1.69.1.2.1.4.19 -> 7f96dyXxJtnibF5
TLV-11[16]: 1.3.6.1.2.1.69.1.2.1.5.19 -> 2 (i32)
TLV-11[17]: 1.3.6.1.2.1.69.1.2.1.6.19 -> HEX:40 00
TLV-11[18]: 1.3.6.1.2.1.69.1.2.1.7.19 -> 4 (i32)
TLV-11[19]: 1.3.6.1.2.1.69.1.2.1.2.20 -> 255.255.255.255
TLV-11[20]: 1.3.6.1.2.1.69.1.2.1.3.20 -> 255.255.255.255
TLV-11[21]: 1.3.6.1.2.1.69.1.2.1.4.20 -> T7f93VpDQWFwyzC
TLV-11[22]: 1.3.6.1.2.1.69.1.2.1.5.20 -> 3 (i32)
TLV-11[23]: 1.3.6.1.2.1.69.1.2.1.6.20 -> HEX:40 00
TLV-11[24]: 1.3.6.1.2.1.69.1.2.1.7.20 -> 4 (i32)
TLV-11[25]: 1.3.6.1.2.1.69.1.6.1.0 -> 1 (i32)
TLV-11[26]: 1.3.6.1.2.1.69.1.6.2.1.2.20 -> 4 (i32)
TLV-11[27]: 1.3.6.1.2.1.69.1.6.2.1.3.20 -> 0 (i32)
TLV-11[28]: 1.3.6.1.2.1.69.1.6.2.1.4.20 -> 1 (i32)
TLV-11[29]: 1.3.6.1.2.1.69.1.6.2.1.5.20 -> 2048 (i32)
TLV-11[30]: 1.3.6.1.2.1.69.1.6.2.1.2.22 -> 4 (i32)
TLV-11[31]: 1.3.6.1.2.1.69.1.6.2.1.3.22 -> 0 (i32)
TLV-11[32]: 1.3.6.1.2.1.69.1.6.2.1.4.22 -> 1 (i32)
TLV-11[33]: 1.3.6.1.2.1.69.1.6.2.1.5.22 -> 2054 (i32)
TLV-11[34]: 1.3.6.1.2.1.69.1.6.3.0 -> 1 (i32)
TLV-11[35]: 1.3.6.1.2.1.69.1.6.4.1.2.10 -> 4 (i32)
TLV-11[36]: 1.3.6.1.2.1.69.1.6.4.1.3.10 -> 2 (i32)
TLV-11[37]: 1.3.6.1.2.1.69.1.6.4.1.4.10 -> 0 (i32)
TLV-11[38]: 1.3.6.1.2.1.69.1.6.4.1.5.10 -> 3 (i32)
TLV-11[39]: 1.3.6.1.2.1.69.1.6.4.1.9.10 -> 24.28.193.96
TLV-11[40]: 1.3.6.1.2.1.69.1.6.4.1.10.10 -> 255.255.255.248
TLV-11[41]: 1.3.6.1.2.1.69.1.6.4.1.2.11 -> 4 (i32)
TLV-11[42]: 1.3.6.1.2.1.69.1.6.4.1.3.11 -> 2 (i32)
TLV-11[43]: 1.3.6.1.2.1.69.1.6.4.1.4.11 -> 0 (i32)
TLV-11[44]: 1.3.6.1.2.1.69.1.6.4.1.5.11 -> 3 (i32)
TLV-11[45]: 1.3.6.1.2.1.69.1.6.4.1.7.11 -> 24.28.193.96
TLV-11[46]: 1.3.6.1.2.1.69.1.6.4.1.8.11 -> 255.255.255.248
TLV-11[47]: 1.3.6.1.2.1.69.1.6.4.1.2.20 -> 4 (i32)
TLV-11[48]: 1.3.6.1.2.1.69.1.6.4.1.4.20 -> 2 (i32)
TLV-11[49]: 1.3.6.1.2.1.69.1.6.4.1.5.20 -> 1 (i32)
TLV-11[50]: 1.3.6.1.2.1.69.1.6.4.1.11.20 -> 17 (i32)
TLV-11[51]: 1.3.6.1.2.1.69.1.6.4.1.12.20 -> 68 (i32)
TLV-11[52]: 1.3.6.1.2.1.69.1.6.4.1.13.20 -> 68 (i32)
TLV-11[53]: 1.3.6.1.2.1.69.1.6.4.1.14.20 -> 67 (i32)
TLV-11[54]: 1.3.6.1.2.1.69.1.6.4.1.15.20 -> 67 (i32)
TLV-11[55]: 1.3.6.1.2.1.69.1.6.4.1.2.21 -> 4 (i32)
TLV-11[56]: 1.3.6.1.2.1.69.1.6.4.1.3.21 -> 2 (i32)
TLV-11[57]: 1.3.6.1.2.1.69.1.6.4.1.4.21 -> 0 (i32)
TLV-11[58]: 1.3.6.1.2.1.69.1.6.4.1.5.21 -> 3 (i32)
TLV-11[59]: 1.3.6.1.2.1.69.1.6.4.1.11.21 -> 17 (i32)
TLV-11[60]: 1.3.6.1.2.1.69.1.6.4.1.12.21 -> 67 (i32)
TLV-11[61]: 1.3.6.1.2.1.69.1.6.4.1.13.21 -> 68 (i32)
TLV-11[62]: 1.3.6.1.2.1.69.1.6.4.1.14.21 -> 67 (i32)
TLV-11[63]: 1.3.6.1.2.1.69.1.6.4.1.15.21 -> 68 (i32)
TLV-11[64]: 1.3.6.1.2.1.69.1.6.4.1.2.30 -> 4 (i32)
TLV-11[65]: 1.3.6.1.2.1.69.1.6.4.1.3.30 -> 2 (i32)
TLV-11[66]: 1.3.6.1.2.1.69.1.6.4.1.4.30 -> 0 (i32)
TLV-11[67]: 1.3.6.1.2.1.69.1.6.4.1.5.30 -> 3 (i32)
TLV-11[68]: 1.3.6.1.2.1.69.1.6.4.1.9.30 -> 24.28.193.6
TLV-11[69]: 1.3.6.1.2.1.69.1.6.4.1.10.30 -> 255.255.255.255
TLV-11[70]: 1.3.6.1.2.1.69.1.6.4.1.2.31 -> 4 (i32)
TLV-11[71]: 1.3.6.1.2.1.69.1.6.4.1.3.31 -> 2 (i32)
TLV-11[72]: 1.3.6.1.2.1.69.1.6.4.1.4.31 -> 0 (i32)
TLV-11[73]: 1.3.6.1.2.1.69.1.6.4.1.5.31 -> 3 (i32)
TLV-11[74]: 1.3.6.1.2.1.69.1.6.4.1.7.31 -> 24.28.193.6
TLV-11[75]: 1.3.6.1.2.1.69.1.6.4.1.8.31 -> 255.255.255.255
Time Of Day completed...
DefaultSnmpAgentClass::SystemTimeChangeEvent for SB5102 CM Agent w/ BRCM Factory Support
Not logging event ID 2291949524, control for level 7 is 0.
Not logging event ID 2291949324, control for level 7 is 0.
SB5102 CM Agent w/ BRCM Factory Support processing TLV-11's
SNMP packet sent to 10.39.121.245:225
75 TLV-11's OK.
Sending a REG-REQ to the CMTS...
Received a REG-RSP message from the CMTS...
0x000434d6 [CmDocsisCtlThread] BcmCmDocsisCtlThread::RegRspMsgEvent: (CmDocsisCtlThread) We registered with a DOCSIS 1.1 config file!
Registration complete!
Process CVC
CmDownloadMatchBuffer - failed on comparison of strings
srcbuf= cmpbuf=^ i=0
0x00043508 [CmDocsisCtlThread] CmSecureDownload::CmCodeVerificationCertificate:TonguearseAndValidate: (Secure Software Download) ERROR - Failed to match digests.
Calculated SHA digest=
5e d9 90 56 7c fa 0f cc 1f bf 62 a0 f5 1e 7c 77
7e 05 d3 8e
RSA decrypted digest=
00 80 01 09 58 00 00 00 00 00 00 00 00 00 00 00
00 30 82 00
0x00043512 [CmDocsisCtlThread] CmSecureDownload:TonguerocessConfigFileSpecifiedCvc: (Secure Software Download) ERROR - Config file co-signer CVC is rejected.
0x00043512 [CmDocsisCtlThread] CmSecureDownload:TonguerocessConfigFileManufAndCosignerCvcs: (Secure Software Download) ERROR - Reject config file MSO CVC!
0x00043512 [CmDocsisCtlThread] BcmCmDocsisCtlThread:TonguerocessCVC: (CmDocsisCtlThread) ERROR - Config file does not include a valid CVC!
DOCSIS CoS/QoS rate shaping enable is now 1
CmSnmpAgent::CmOperationalEvent for SB5102 CM Agent w/ BRCM Factory Support
CmSnmpAgent operating in 1.1 mode, including docsQos, excluding docsBpi
+++ No DH kickstart profiles or snmpCommunityTable entries installed.
We will operate in NMACCESS mode.
SB5102 CM Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
SB5102 CM Agent w/ BRCM Factory Support enabling management.
SB5102 CM Agent w/ BRCM Factory Support sending deferred traps...
Done w/ deferred traps.
SB5102 CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
0x0004351c [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchBpkm: (CmDocsisCtlThread) BPKM enabled. starting BPKM key requests.
Logging event: Configuration File CVC Validation Failure
Sending syslog message from IF 1 to 24.29.99.57:
<131> CABLEMODEM [DOCSIS]: <69020700> Configuration File CVC Validation Failure Config File: ?BBgdiTUAFOglkTQKJ3n1@Cid59TarFSmSIKIj+GFt_lVNYDxIZxfs - TFTP Server: 24
SB5102 CM Event Log w/ BRCM Factory Support sending deferred async messages...
Done w/ deferred msgs
Not logging event ID 66040100, control for level 7 is 0.
BPI initialization completed. Calling ConfigOperational().
Enabling network access for all CPE ports.

mot_scanList: Writing to Flash!
BcmCmDocsisStatusEventCodes::kCmIsOperational
Suspending SNMP Thread
0x0004371a [CmDocsisCtlThread] BcmVendorCmApplication::StopDhcpServer: (VendorExtension CmApp) Shutting down DHCP Server...
0x0004371a [CmDocsisCtlThread] BcmStandbySwitchThread::CmIsOperational: (Motorola Standby Switch Thread) Simulating a press of the standby switch to get the state configured properly.
0x00043724 [IGMP Thread] BcmIgmpThread::Starting Igmp Thread...: (IGMP Thread)
0x00043724 [Motorola Standby Switch Thread] BcmStandbySwitchThread::ThreadMain: (Motorola Standby Switch Thread) Standby switch was pressed!
0x00043724 [Motorola Standby Switch Thread] BcmStandbySwitchThread:TonguerocessSwitchEvent: (Motorola Standby Switch Thread) Standby switch disabled in nonvol; ignoring event.
Not logging event ID 2296948624, control for level 7 is 0.

CM> \cd..
CM> \cd..

Error - Unknown command: 'cd..'

CM> dir
CM>
CM> dir

! ? REM cd dir
find_command help history instances ls
man pwd sleep syntax system_time
usage
----
con_high mbufShow memShow mutex_debug ping
read_memory reset routeShow run_app shell
stackShow taskDelete taskInfo taskPrioritySet taskResume
taskShow taskSuspend taskTrace usfsShow version
write_memory zone
----
[HeapManager] [cm_hal] [docsis_ctl] [embedded_target] [enet_hal] [event_log]
[flash] [forwarder] [ip_hal] [msgLog] [non-vol] [pingHelper] [snmp] [snoop]
[usb_hal]

CM> cd  dir
CM>
CM> dir

! ? REM cd dir
find_command help history instances ls
man pwd sleep syntax system_time
usage
----
con_high mbufShow memShow mutex_debug ping
read_memory reset routeShow run_app shell
stackShow taskDelete taskInfo taskPrioritySet taskResume
taskShow taskSuspend taskTrace usfsShow version
write_memory zone
----
[HeapManager] [cm_hal] [docsis_ctl] [embedded_target] [enet_hal] [event_log]
[flash] [forwarder] [ip_hal] [msgLog] [non-vol] [pingHelper] [snmp] [snoop]
[usb_hal]

CM> ls
CM>
CM> ls

! ? REM cd dir
find_command help history instances ls
man pwd sleep syntax system_time
usage
----
con_high mbufShow memShow mutex_debug ping
read_memory reset routeShow run_app shell
stackShow taskDelete taskInfo taskPrioritySet taskResume
taskShow taskSuspend taskTrace usfsShow version
write_memory zone
----
[HeapManager] [cm_hal] [docsis_ctl] [embedded_target] [enet_hal] [event_log]
[flash] [forwarder] [ip_hal] [msgLog] [non-vol] [pingHelper] [snmp] [snoop]
[usb_hal]

CM> cd
CM>
CM> cd di  doc
CM> cd doc

Active Command Table: CM DOCSIS Control Thread Commands (docsis_ctl)

CM -> docsis_ctl

CM/DocsisCtl> up_dis
CM/DocsisCtl>
CM/DocsisCtl> up_dis

Simulating UP-DIS message.

Received an UP-DIS message from the CMTS!

Mode = disable transmitter
BcmCmDocsisStatusEventCodes::kCmIsNotOperational
0x0005f8ac [CmDocsisCtlThread] BcmVendorCmApplication::StartDhcpServer: (VendorExtension CmApp) Starting DHCP Server!
0x0005f8ac [IGMP Thread] BcmIgmpThread::Stopping Igmp Thread...: (IGMP Thread)
CamDeleteAddress: Deleted address from cam segment 0
Not logging event ID 2436694041, control for level 7 is 0.
0x0005f8e8 [CmBpiManagerThd] BcmDocsisCmHalIf::SelectActiveBpiKey: (DOCSIS CableModem HalIf) WARNING - BPI is now disabled!

CM/DocsisCtl> Deleting DOCSIS 1.0 CoS Settings for SID 0x1897
0x0005f974 [CmDocsisCtlThread] BcmDocsisCmHalIf:Big GrineleteAllServiceFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service Flows, along with associated Classifiers and PHS rules...
Stopping DHCP/ToD/TFTP (client requested)...
The ToD thread was stopped.
DHCPc: Releasing the lease with client id htype=1, value=00:14:e8:25:91:34
DHCPc: Sending Release packet; client id htype=1, value=00:14:e8:25:91:34
0x0005f97e [DHCP Client Thread] BcmDhcpClientIf::SendDhcpPacket: (DHCP ClientIf for IP Stack1) WARNING - Failed to send packet!
0x0005f97e [DHCP Client Thread] BcmDhcpClientIf::SendRelease: (DHCP ClientIf for IP Stack1) WARNING - Failed to create/send Release packet! Oh, well, no biggie...
0x0005f97e [DHCP Client Thread] BcmEcosIpHalIf::RemoveLeaseImpl: (IP Stack1 HalIf) Removing lease IP address 10.39.121.245 from IP stack 1
0x0005f988 [DHCP Client Thread] BcmEcosIpHalIf::RemoveLeaseImpl: (IP Stack1 HalIf) This is the last address on the stack; shutting the stack down:numberOfAddresses=1
0x0005f988 [DHCP Client Thread] BcmEcosIpHalIf::ShutdownIpStackImpl: (IP Stack1 HalIf)
Shutting down IP stack 1
DefaultSnmpAgentClass::RestartPendingEvent for SB5102 CM Agent w/ BRCM Factory Support
SB5102 CM Agent w/ BRCM Factory Support resetting to default state.
SB5102 CM Agent w/ BRCM Factory Support destroying users...
Pausing trap thread
SB5102 CM Agent w/ BRCM Factory Support destroying notifies...
Resuming trap thread
SB5102 CM Agent w/ BRCM Factory Support destroying views...
SB5102 CM Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted
SB5102 CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisCpeView
Non-Vol Settings successfully written to the device.
0x0005fa96 [CmDocsisCtlThread] BcmCmDocsisCtlThread::ResetRngState: (CmDocsisCtlThread)

@@@@@ In ResetRngState, fRemainingInitRngPowerSteps 17
0x0005fa96 [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Downstream Channel scan stopped!
0x0005faaa [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncStop: (CmDocsisCtlThread)

*
* Locking off-frequency so that we don't receive any
* messages or data. Ignore the scan messages that follow...
*

Timeout is forever; stopping timer.
0x0005faaa [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Scanning for a Downstream Channel...

mot_scanList: Setting override freq @ 7000000
Scanning DS Channel at 7000000 Hz... (Initial target freq)

CM/DocsisCtl> Found energy at frequency 7000000Hz! Publishing event kEventEnergyDetected...
cd
CM/DocsisCtl>
CM/DocsisCtl> cd /
CM/DocsisCtl> cd /

Active Command Table: CM DOCSIS Commands (CM)

CM

CM> cd
CM>
CM> cd n/b
CM> cd n/b

Active Command Table: BFC Application Settings Commands (bfcApp)

CM -> non-vol -> bfcApp

CM/NonVol/BfcApp> auto_console
CM/NonVol/BfcApp>
CM/NonVol/BfcApp> auto_console 1
CM/NonVol/BfcApp> auto_console 1

Automatically stop at console = 1

CM/NonVol/BfcApp> write
CM/NonVol/BfcApp>
CM/NonVol/BfcApp> write

Dynamic Non-Vol Settings successfully written to the device.
Permanent Non-Vol Settings successfully written to the device.

CM/NonVol/BfcApp> reboot
CM/NonVol/BfcApp> reboot

Error - Unknown command: 'reboot'

CM/NonVol/BfcApp> exit
CM/NonVol/BfcApp> exit

Error - Unknown command: 'exit'

CM/NonVol/BfcApp> cose
CM/NonVol/BfcApp> cose

Error - Unknown command: 'cose'

CM/NonVol/BfcApp> close
CM/NonVol/BfcApp> close

Error - Unknown command: 'close'

CM/NonVol/BfcApp> cd..
CM/NonVol/BfcApp> cd..

Error - Unknown command: 'cd..'

CM/NonVol/BfcApp> cd..
CM/NonVol/BfcApp> cd..

Error - Unknown command: 'cd..'

CM/NonVol/BfcApp> cd.
CM/NonVol/BfcApp> cd.

Error - Unknown command: 'cd.'

CM/NonVol/BfcApp> cd.
CM/NonVol/BfcApp> cd.

Error - Unknown command: 'cd.'

CM/NonVol/BfcApp> cd..
CM/NonVol/BfcApp> cd..

Error - Unknown command: 'cd..'

CM/NonVol/BfcApp> up_dis
CM/NonVol/BfcApp> up_dis

Error - Unknown command: 'up_dis'

CM/NonVol/BfcApp>





***************************************************************************************************************************************************************************************************************************************************************************************************************

I will also post a new topic about this maybe some one can shed light to this solution.


Yours truly therealdeal.


RE: I'm trying to get a telnet log - bxmacho - 18-04-2013

I'm no expert but I believe your problem lies here!!!
And i believe they trying to update your software!
The CM config must contain this C-CVC and/or M-CVC in order to allow 1.1 compliant CM to download the code file from TFTP server regardless the CM is provisioned to run with BPI,BPI+, or none of them.
But maybe one of the experts can shine light on it, or correct me if im wrong..

0x00043512 [CmDocsisCtlThread] CmSecureDownload:TonguerocessConfigFileSpecifiedCvc: (Secure Software Download) ERROR - Config file co-signer CVC is rejected.
0x00043512 [CmDocsisCtlThread] CmSecureDownload:TonguerocessConfigFileManufAndCosignerCvcs: (Secure Software Download) ERROR - Reject config file MSO CVC!
0x00043512 [CmDocsisCtlThread] BcmCmDocsisCtlThread:TonguerocessCVC: (CmDocsisCtlThread) ERROR - Config file does not include a valid CVC!