+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: DPC 2100 R2 Orignal Firmware needed. (/showthread.php?tid=2234)
Pages:
1
2
DPC 2100 R2 Orignal Firmware needed. - Baxter - 05-01-2013
Haxorware causing issues with ISP Need original firmware for DPC2100 R2. Anyone have a link?
RE: DPC 2100 R2 Orignal Firmware needed. - southernyankey1970 - 06-01-2013
Here
RE: DPC 2100 R2 Orignal Firmware needed. - Baxter - 06-01-2013
(06-01-2013, 03:54 AM)southernyankey1970 Wrote: Here
Thanks Dude !
RE: DPC 2100 R2 Orignal Firmware needed. - Baxter - 06-01-2013
It didn't take. I tried via the web gui, telnet/tftp, and no luck. Maybe bad image? Any other ideas?
Via Telnet it starts reading blocks and finally gives up and says it cannot open the bin file.
Uploading it via the gui fails because it says its not a valid file...
RE: DPC 2100 R2 Orignal Firmware needed. - drewmerc - 06-01-2013
try this one http://www.haxorware.com/forums/thread-2121-post-15813.html#pid15813
RE: DPC 2100 R2 Orignal Firmware needed. - Baxter - 07-01-2013
It seemed to have taken the new one , yet now its not doing anything and I cannot access it at all with tftp , the gui over IP or anything. Is there a way in via usb or is this thing bricked?
It looks like I am all solid and one light blinking on PC status.
This has happened before and it came back , but cannot remember what I did to make that happen.
RE: DPC 2100 R2 Orignal Firmware needed. - Baxter - 07-01-2013
(07-01-2013, 03:40 AM)Baxter Wrote: It seemed to have taken the new one , yet now its not doing anything and I cannot access it at all with tftp , the gui over IP or anything. Is there a way in via usb or is this thing bricked?Heads Up I have also just tried the OneClick Drew posted on another similar thread and it appears to only work via ip/telnet which is unreachable at this point because its not pingable.
It looks like I am all solid and one light blinking on PC status.
This has happened before and it came back , but cannot remember what I did to make that happen.
Will JTAG work on this if I do all that? Or is this thing bricked for good?
RE: DPC 2100 R2 Orignal Firmware needed. - drewmerc - 07-01-2013
jtag should bring anything back baring hardware faults, tho if you have a ttl cable handy i'd try that first
RE: DPC 2100 R2 Orignal Firmware needed. - Baxter - 07-01-2013
Okay.; Thanks . This is what I have now and this is what I want to achieve if possible. I already have a rs232toUSB adapter (commonly used to connect to cisco routers) With a normal console pinout on the serial side. Having said that, Should all I have to do is solder on a male serial port onto the jtag pins on the modem?
RE: DPC 2100 R2 Orignal Firmware needed. - drewmerc - 07-01-2013
your rs232 should do fine, here's the pinout (the one on the right)