+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: Upgrade to 11 rev 32 (/showthread.php?tid=218)
Upgrade to 11 rev 32 - geo - 22-06-2009
Hi guys, I'm new on this forum and I hope that you can help me.
I have installed on my modem (AMBIT) the harxorware 1.0 rc 4 working fine, now I want to upgrade my modem to the last version (11 rev 32), but I have dudes about that.
When I did install the actual version I didn't backup of the original soft, my question is: can I do the Upgrade over the 1.0rc4 without come back to the original version????
Thanks a lot for your answer.
Geo
RE: Upgrade to 11 rev 32 - rajkosto - 27-06-2009
sure
RE: Upgrade to 11 rev 32 - hackallday - 12-07-2009
(27-06-2009, 05:15 AM)rajkosto Wrote: sure
I'm trying to do the same thing. But gives me an error. I'm using Haxorware 1.0rc6 and am trying to upgrade to the latest (1.1 v 32)
I Have a SB5101 Running 1.0rc6 (2meg)
would like to updated to the latest but get an error message when trying to use the GUI Firmware upgrade and when i jtag the device it fails to boot and have to reflash the old fm -=( It says you didn't upload a valid firmware image. No changes have been made.
Thanks for the help
RE: Upgrade to 11 rev 32 - therebel - 12-07-2009
(12-07-2009, 11:08 AM)hackallday Wrote:(27-06-2009, 05:15 AM)rajkosto Wrote: sure
I'm trying to do the same thing. But gives me an error. I'm using Haxorware 1.0rc6 and am trying to upgrade to the latest (1.1 v 32)
I Have a SB5101 Running 1.0rc6 (2meg)
would like to updated to the latest but get an error message when trying to use the GUI Firmware upgrade and when i jtag the device it fails to boot and have to reflash the old fm -=( It says you didn't upload a valid firmware image. No changes have been made.
Thanks for the help
Hey..have u tried telnet method...?.It worked for me...
READ the instructions in the haxorware f/w folder....
RE: Upgrade to 11 rev 32 - hackallday - 13-07-2009
Yea, thats how i bricked the modem had to jtag it back to life with the old bin again -=)
RE: Upgrade to 1.1 rev 32 - Tyfon - 25-07-2009
Yeap same here gu'ys
The instruction were to reflash the modem to the original bin..
the reflash to Hax1.1 rev32. when I did that
it wrote two sectors there were errors, I notice if it has AMD
chip it will have alot of errors but if ti has INTEL it will do just fine on JtagUtility but the modem will not go on line.
I dot now why! So right now I have no Internet for the last weeks
at the moment I'm using this one d11_m_sb5101_silver_c01.cm
and no dice maybe someone can enlight the error that we are doing..
Also the Update /upgrade from Rev 30 to Rev32 are not clear
for my knowledge maybe some can post something a little clear.
Thanks for the help guy's
Tyfon
RE: Upgrade to 11 rev 32 - drewmerc - 25-07-2009
the instructions are very simple and easy to understand
Quote:Set your computers ip to 192.168.100.10
Set up a TFTP server with haxorware11rev32.bin in its root
Make sure the haxorware webgui isn't currently open
Connect to modem with hyperterminal or telnet to the IP 192.168.100.1
Enter your username and password
cd /ip
ipconfig 1 release
y
dload -i 1 -l -f 192.168.100.10 haxorware11rev32.bin
y
cd /
reset