Haxorware Forums
SBG900 Factory Mode - Printable Version

+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: SBG900 Factory Mode (/showthread.php?tid=139)



SBG900 Factory Mode - jawlinski - 02-04-2009

I want to set sbg900 in factory mode.
Like "Haynes Cable Modem Guide Rev1.7.2.pdf" p 113 f I need
a bit file "sbg900.bit". Where can I find the file? Google does not
help.

thanks
p.j.


RE: SBG900 Factory Mode - dako_18 - 02-04-2009

No only need the vxwork for Sb5100 ok


RE: SBG900 Factory Mode - jawlinski - 06-04-2009

thanks

i am online with a motorola 5101 modem
and i want use a sbg900 modem instead
the 5101.

i enabled factory mode of sbg900 und changed
hfc mac address and serial number.
the modem can download the sb5101.cfg file
from isp but than i get an auth reject
(B301.08)
Do I have to change some modem
certs like:

1.3.6.1.4.1.1166.1.19.4.52.0 cmFactoryCMCertificate
1.3.6.1.4.1.1166.1.19.4.53.0 cmFactoryManCertificate
1.3.6.1.4.1.1166.1.19.6.3.7.0 cmCfgVendorId
1.3.6.1.4.1.1166.1.19.6.3.8.0 cmCfgVendorSpecific
1.3.6.1.4.1.1166.1.19.4.50.0 cmFactoryBigRSAPublicKey
1.3.6.1.4.1.1166.1.19.4.51.0 cmFactoryBigRSAPrivateKey

thanks
p.j.


RE: SBG900 Factory Mode - fuxord - 25-08-2016

(06-04-2009, 12:40 PM)jawlinski Wrote: thanks

i am online with a motorola 5101 modem
and i want use a sbg900 modem instead
the 5101.

i enabled factory mode of sbg900 und changed
hfc mac address and serial number.
the modem can download the sb5101.cfg file
from isp but than i get an auth reject
(B301.08)
Do I have to change some modem
certs like:

1.3.6.1.4.1.1166.1.19.4.52.0 cmFactoryCMCertificate
1.3.6.1.4.1.1166.1.19.4.53.0 cmFactoryManCertificate
1.3.6.1.4.1.1166.1.19.6.3.7.0 cmCfgVendorId
1.3.6.1.4.1.1166.1.19.6.3.8.0 cmCfgVendorSpecific
1.3.6.1.4.1.1166.1.19.4.50.0 cmFactoryBigRSAPublicKey
1.3.6.1.4.1.1166.1.19.4.51.0 cmFactoryBigRSAPrivateKey

thanks
p.j.

Hi there, Factory mode could be set using the VxWorks.st file for the SBG900 model. I have tried it and it works. For me however, I was unfortunately not able to get any of the above mentioned OID's. Not sure why OID's did not work. PS: I am just a newbie and everything i have tried is based on researches conducted by experts. Forgive me if this is not as helpful as if you would expect it to be =)


RE: SBG900 Factory Mode - Genghis - 26-08-2016

You're not expecting somebody to b seated out there over 7 years on a forum waiting for answer your questions, do you? You better start a new thread with your case.