![]() |
Help with sb5101E upstream ranging - Printable Version +- Haxorware Forums (http://www.haxorware.com/forums) +-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6) +--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7) +--- Thread: Help with sb5101E upstream ranging (/showthread.php?tid=3599) |
RE: Help with sb5101E upstream ranging - bleros - 10-06-2015 (10-06-2015, 03:58 PM)Canis-Major Wrote: All I can figure out rifght now is it's dropping too much lol, chance's are your isp is trying to kick you, or you have a mac too lose to you and both you and the 'donor' modem are fighting to stay on? Haha sorry for my english ![]() RE: Help with sb5101E upstream ranging - Canis-Major - 10-06-2015 (10-06-2015, 06:44 PM)bleros Wrote:(10-06-2015, 03:58 PM)Canis-Major Wrote: All I can figure out rifght now is it's dropping too much lol, chance's are your isp is trying to kick you, or you have a mac too lose to you and both you and the 'donor' modem are fighting to stay on? Okay, first, is it a d3 mac? or d1? Secondly, can you get online with any other mac? 'Cause 100 miles is a bit far tbh... try someone other side of town.. or a block or two away.. RE: Help with sb5101E upstream ranging - neo_ - 10-06-2015 (10-06-2015, 06:44 PM)bleros Wrote: Haha sorry for my english Meters or miles? RE: Help with sb5101E upstream ranging - bleros - 10-06-2015 (10-06-2015, 08:16 PM)neo_ Wrote:(10-06-2015, 06:44 PM)bleros Wrote: Haha sorry for my english 100meters or 150meters RE: Help with sb5101E upstream ranging - neo_ - 10-06-2015 (10-06-2015, 08:29 PM)bleros Wrote:(10-06-2015, 08:16 PM)neo_ Wrote:(10-06-2015, 06:44 PM)bleros Wrote: Haha sorry for my english Too close. You are getting a MAC collision, knocking both of your modems offline. You need to get a MAC address from a different node. RE: Help with sb5101E upstream ranging - bleros - 14-06-2015 Quote:Okay, first, is it a d3 mac? or d1? What d3 d1? idont understand.. yes i get online i just tested mac around 500m away help me about uncapp what number need to edit inside .cm RE: Help with sb5101E upstream ranging - Canis-Major - 14-06-2015 D3 mac is anything above one tuner in a nutshell.. anything previous is capable of d1, d1.1, and d2, and since there is 4 modes of d whatever under the guise of BPI: off, bpi, bpi ON (cert's with bypass) and bpi+ - screwed if you fell for cloning cons-piracy-theorist's.. RE: Help with sb5101E upstream ranging - bleros - 14-06-2015 (14-06-2015, 02:33 AM)Canis-Major Wrote: D3 mac is anything above one tuner in a nutshell.. anything previous is capable of d1, d1.1, and d2, and since there is 4 modes of d whatever under the guise of BPI: off, bpi, bpi ON (cert's with bypass) and bpi+ - screwed if you fell for cloning cons-priracy-theorist's.. BPI is off.. i noticed with this 2st mac modem is coming online faster than first mac? tell me abt config which numbers to edit to test it thanks major RE: Help with sb5101E upstream ranging - Canis-Major - 14-06-2015 Oh, and you wont find a d3 mac using anything from a d1 network, unless of couse, you have a scource ip to work from ![]() The faster a mac comes on, the more legit it 'appear's' in your non-vol (no need to check what matches) Oh, and before I go.. here, the non-vol is set by config, get over it. RE: Help with sb5101E upstream ranging - bleros - 14-06-2015 Should i enable this again? /non-vol/halif/eth_reject_cam 1 /non-vol/write both |