+- Haxorware Forums (http://www.haxorware.com/forums)
+-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6)
+--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7)
+--- Thread: EPC2100R2 eror , please come (/showthread.php?tid=420)
RE: EPC2100R2 eror , please come - drewmerc - 14-02-2010
Before you start, download and install putty:
Code:
http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe
Method 1 is preferred in all cases, method 2 looks worse than it is lol.
Method 1) Using MAX232
Remove power from the modemConnect your MAX232 adapter to the modem header and the PC. This guide assumes you're using COM1.
Open Putty. Click the logging section of the settings panel. Select the following options:
Session logging: All session output
Click 'browse' and browse to your desktop folder.
Filename: putty.txt
'Always overwrite it'
Untick 'flush log file frequently'
Click back onto the 'session' section of the settings panel:
Connection type: Serial
Serial line: COM1
Speed: 115200
Close window on exit: Never
Click 'open', then plug the power into the modem.
You should see the boot process and connection attempt appear.
Wait for about 20s after the connection has reached the failure point, then close putty and it'll save the txt log as putty.txt on your desktop.
Method 2) Using ethernet or USB (USB requires that USB drivers are correctly installed)
Remove power from the modem.
Set manual NIC IP 192.168.100.10.
Open Putty. Click the 'session' section of the settings panel:
Connection type: Telnet
Host Name: 192.168.100.1
Port: 23
Close window on exit: Never
Power up the modem. Wait 15 seconds, then click 'open' in putty.
Enter username and password, press enter.
Ignore any crap coming up in the window, it may look like you can't type but you can. May help if you just don't look at the screen
Type this, pressing enter at the end of each line:
cd doc
up_dis
cd /
cd n/b
auto_console 1
write
Note: The lines above are correct for modems based on the BCM3349 (A250/A255/A256/SB5101/Webstar 2100). If you're using a BCM3348 modem (A200/SB5100) the line 'cd n/b' changes to 'cd n/c'.
This tells the modem to halt at the console. Close putty and reboot modem using power cable.
When you reboot it, it won't try to connect at first, so you have time to set putty to log all console output to txt before connecting.
Open Putty. Click the logging section of the settings panel. Select the following options:
Session logging: All session output
Click 'browse' and browse to your desktop folder.
Filename: putty.txt
'Always overwrite it'
Untick 'flush log file frequently'
Click back onto the 'session' section of the settings panel:
Connection type: Telnet
Host Name: 192.168.100.1
Port: 23
Close window on exit: Never
Click 'open', enter username and password and press enter. Type 'run' and press enter. The modem will try to connect.
Wait for about 20s after the connection has reached the failure point, then close putty and it'll save the txt log as putty.txt on your desktop.
Once you've finished you'll need to set auto_console back to 0 in telnet, or you'll have to type 'run' every time you reboot modem.
RE: EPC2100R2 eror , please come - rebornishard - 14-02-2010
is there any possible way ?
i'm not have max232
but i have EPC2100R2 USB (without driver)
thanks for your guide , i respect that
RE: EPC2100R2 eror , please come - drewmerc - 14-02-2010
Method 2) Using ethernet it's there
RE: EPC2100R2 eror , please come - rebornishard - 14-02-2010
(14-02-2010, 05:19 PM)drewmerc Wrote: Method 2) Using ethernet it's there
![[Image: 31Ajtf3NkJL.jpg]](http://ecx.images-amazon.com/images/I/31Ajtf3NkJL.jpg)
i don't have that blue cable usb driver, where i can find it
thanks again
RE: EPC2100R2 eror , please come - drewmerc - 15-02-2010
why do you keep going on about usb for, how the hell are you connecting it to you computer fucking magic
Quote:ethernet or USB
the instructions i posted work with all connections possible
as per your pic
ethernet = the gray wire (i'll guess you use this unless you are using magic)
usb = blue wire (that you dont have)
max232 = not shown (that you dont have)
RE: EPC2100R2 eror , please come - rebornishard - 15-02-2010
(15-02-2010, 12:07 AM)drewmerc Wrote: why do you keep going on about usb for, how the hell are you connecting it to you computer fucking magici has blue cable
Quote:ethernet or USB
the instructions i posted work with all connections possible
as per your pic
ethernet = the gray wire (i'll guess you use this unless you are using magic)
usb = blue wire (that you dont have)
max232 = not shown (that you dont have)
it's one pack with the modem
so what next ?
thanks
RE: EPC2100R2 eror , please come - drewmerc - 15-02-2010
http://haxorware.com/forums/search.php?action=results&sid=4022a0b825eadf7782326b5ff27f1b08&sortby=lastpost&order=desc
and before you say that you dont have an ambit read the thread as the drivers that are posted are motorolla ones
why because haxor is moto based
RE: EPC2100R2 eror , please come - rebornishard - 15-02-2010
(15-02-2010, 08:18 AM)drewmerc Wrote: http://haxorware.com/forums/search.php?action=results&sid=4022a0b825eadf7782326b5ff27f1b08&sortby=lastpost&order=desci download it, and then unzip it
and before you say that you dont have an ambit read the thread as the drivers that are posted are motorolla ones
why because haxor is moto based
just click unzip
i don't know where i must put it
thanks a lot
RE: EPC2100R2 eror , please come - drewmerc - 15-02-2010
http://www.google.com/search?q=manual+driver+install
RE: EPC2100R2 eror , please come - pytyhon1564 - 17-02-2010
When I type in the command "cd n/b" it says "Specified subtable ('b') doesn't exist! Can't change to it..." and every command after fails. I have a sb5101 but I tried "cd n/c" for shits and giggles, but I got the same error.